Josh, I see you have joined the HT600E group, if you have a look at the last two weeks worth of messages you will see that there are some MT6000E's for sale

Hi,
Merry Christmas to all! Recently, I purchased a surplus Non-public safety microphone(NM6242B) to use in place of a commander microphone that I gifted away in a trade. I love it, it works great.
Aside from that...how are you supposed to wear it with your radio on a duty belt? If I clip it on my ...

Yes you could use the Codeplug from another MT6000E, you might need to use the 'Lab' version of the programming software to get the radio to accept it.. The downside of doing this is you would end up with a radio that has the tuning/calibration settings of the donor radio

Sounds like the Codeplug is corrupted..
With luck you have saved a copy of the Codeplug and can program it back into the radio??

indyarmor wrote:Where can you purchase one of these?

They pop up from time to time on eBay UK..

Whereupon PM sent

They do not make any noise when programming... the cloning cable does not have pin 7 connected either.
The only reason pin 7 is shown grounded is that the circuit is from the service cable and it is required to route RX audio to the 4005 service box.. But as a programming only cable it is not ...

For the RIB to radio cable it's wired as follows..

RIB DB25 / RADIO CONNECTOR
1 / 7&5
24 / 6
8 / 9

4 to 11 Jumper on the DB25

The connection on pin 7 of the radio connector is not required..

MT1000, HT600, HT800 etc.

For anyone who has purchased a light grey coloured Motorola RIB box off of eBay in the UK and found that it does not work with their RIB to Radio leads, this might be of help. The PCB inside the box is marked 'FVMaster', in their descriptions they say the RIB is pin-for-pin compatible with the ...

Enable 'Inhibit Selection' in the 'Channel Definitions' menu, that way only the 'Channel Alias' will be displayed..
Also in the 'Channel Alias definitions' make sure that 'Alternate Display' is disabled otherwise it will alternate between the channel number and the alias..

Yes they are..

Thanks very much Will and Bernie, it is most appreciated.

Mike

I should have looked to see if he had posted recently..

... we made several mods to the HT600/P200 bank chargers especially those used in the movie industry. Basically changing one resistor and one capacitor per slot. The battery normally gets warm then the charger switches to so-called trickle charge rate but the current is too much and the battery ...

...Best to try one in a Standered Rapid Charger, and see
how it performs there, if it performs OK in a single unit
Raoid Charger, perhaps you may have some Bad Mulit-unit
Chargers.

There is a item you can build to test the slots if you want to
go to all the trouble...


Hi Monty, can you cast ...

hi all need help with hex got a ht600e 0n uhf 438 to 470 need to go to 433 for 4m can this be done or has someone got progame to do this thanks laz

You might like to join our HT600E Yahoo group in the UK, we have lots of info and an out of band codeplug generator. The HT600E will work down to ...

Correct..

Are you using MTSX RSS V6.05 and GP900 RSS ?? If so you will need the MT6000E RSS or GP900-99 RSS..

For the one with bad receive, check to make sure you don't have a broken antenna jack connection on the rf board, very common with the Genesis series. And if it was broken it would still transmit, though eventually you will have a dead PA because of it.. Seen it plenty of times...

Had one on the ...

Hi William, if you are using the MT1000 RSS:
Connect radio to RIB and PC.
Switch radio on.
Run the RSS.
F3 - Get/Save/Program.
F2- Read Radio.
F10 - Return to main menu.
F2 - Service: alignment.
F3 - Squelch and Volume alignment.
Top right hand corner: VOLUME.
Highlight Volume and hit F1 for an ...

The other alternative is to get hold of an HT600E Public Safety speaker/mic, has a TNC socket on the mic that connects to the RF contacts on the facilities connector and works with all the Genesis series..

likimkim wrote:Hello there,
Could yours tell me that which RSS is used to programme HT600e?

There is an HT600E specific RSS but it is a cut down version of the MT1000 RSS, it is designed to be run on a floppy and has no signalling options.. As has been said the MT1000 RSS will do everything you want..

Have a look here:

http://www.446user.co.uk/forum_topic_2794.html

There is a version of the RSS for the MT6000E, it is GP900-99ch with support for Marconi MASC encryption - EVN4602..

In the UK the same speaker/mic but with a straight cord goes under a part number of NMN6241, the third button is an orange Emergency button for use on MT/MTS2000..

Exactly what I did Nick, the only extra things I did were.. Araldite the used wires to the back of the PCB after soldering, and put some Araldite in the unused 3.5mm socket, so that nobody else could try and put audio into the socket..

You need to go to the service Menu (F2) to adjust it.

Daniel.
That was my initial guess as well, but sadly no there is no PL deviation adjustment in the GP900/GM900 range.

Motorola sent out a European Technical Information Bulletin in 1996:

'... the GVN6018A (program on 3.5inch disk) 900 series ...

Anybody got any ideas on how to reduce the PL Tone level on a GP900??

Thanks.

Someone who goes and buys an Astro Saber to listen to their local Police did not buy it to be discreet...

I use a 16 channel GP300-5T / Select 5 for working amateur repeaters in the UK, for this it is ideal - Channel Scan, PL on TX and RX, Live DTMF for ILink enabled repeaters and the 5 Tone tailored to give a RAT tone at the push of a button..
If you would like a copy of the codeplug from my radio ...

.....Speaking of PSM's, is it my imagination or whatever happened to the NMN6194's? In my MTS2000 and my MTX8000 user guides, these are mentioned to be "Stanard microphone; inludes antenna (SMA) UHF, 800/900MHz (VHF capable) COILED CORD ASSEMBLY, 3.5mm ear jack, swivel and RECIEVE AUDIO HIGH LOW ...

Well, I have this problem, I was programing my radio gp300-5t actually, I was in mode radio aligment, when power turned off I mean on power of my computer, now my radio blinks (red, yellow and green), I can' :oops: t read or write to radio. I allways get codeplug error 1.


I got a GP300-5T about ...