Batboard

Will

Got it George. I will fix them up for you. (email sent)

Will

Pin 8 RUS PL/DPL &CSQ DET
Pin 3 PTT
Pin 2 MIC

Will

Bill_G wrote: You can always put an external speaker on it.

A good way to see if the internal speaker is bad. Bill G gets a star.......

Will

" A piece of foam pipe insulation around the pipe. Looking for a better foam piece."

I use racing bicycle handlebar covering, most high end bike shops carry many types.

Will

Steve, there is a whole sub forum for IFR equipment.

Will

He's right down the road from me. If he still has problems I may be able to help.

Will

You can pick up RX audio that is not affected by the volume control on pin 11 of the accessory connector. This is line level or there about and could be feed into a PA amp for the station or your remote adapter.

Pin 11 Filtered Audio
Pin 7and 9 ground

Will

There is a fix for the W4, 5 and 7 series control heads. Move one jumper and add a resistor where the jumper was removed.

Will

The info is on repeater-builder.

Will

Always make sure you can read the radio FIRST. Save the 'codeplug' information to a safe place before making any changes so you can fall back if needed.

Are you running the HT1000 RSS in DOS only?

Will

RF_Burns wrote:Ok, works as designed, not as expected.
I'll try the "BLANK" trick

Thanks

Correct, just do not put a name in for 'that channel'.

Will

Reminds me of Motorola motorcycle radios. They were black, white, and chrome, and had the volume, squelch, chan sel, ect in the speaker.

Great find...

Will

Alex,

Thank you for all your hard work.

Will

I have a Motorola GM300 mic on my ICOM7200 HF rig.

Will

http://batlabs.com/images/mtsxacc.gif

NOTE, the 'speaker leads' can NOT be grounded, the audio output stage amp is push-pull bridging type.

Will

I can NOT say IF the 'battery eliminator' has a voltage regulator in it. I doubt they had a regulator, maybe a blocking/reverse polarity diode. These were used on the test bench. The dual banana plug was for DC input. You could measure the voltage on the 'battery contacts'. http://www.ebay.com/itm/N...

Will

The switching for the internal speaker is handled by the Options Sel line on the side connector.

Will

Actually the R1225 IS very different than the GM300 series. The high, 40 watt, PA has problems overheating even with the bigger heatsink, and the current sense resistor gets fried also. Two big problems in original assembly of the PA board in the heatsink. /\/\ used too much of a poor quality heatsi...

Will

Looks normal to me, most have some gap due to manufacturing tolerances.

Will

Thank you Steve.

Too bad they do not have something like that for a 2012 Jeep Liberty Sport.......

Will

I would say NO, those Aztec chargers had problems.

Will

Did you look on Ford's up fitters web pages?

Will

Have you checked that the CM300 accessory connecter is programed correctly?

RX audio needs to come off RX Filtered pin. TX mic source and PTT need to be set.

Will

There was a mod that grounded the top or escutcheon.

Will

jmr061 is correct on the alignment. People jam in a codeplug and the alignment and calibration values are not correct for that radio.

You need to do a full alignment and calibration first.

Will

You're hosed by the problem period. Nobody makes a radio with the kind of rejection you require. You need to beat on the coordinators to get your split to match the incumbents. Or leave the site. I echo Bill's sentiments to a tee. Unless you are willing to narrowband the system AND THE USERS, time ...

Will

jmr061 wrote:"new" s-record will need to be forced into the radio and the tuning values transferred.

And or a complete realignment and calibration. The command board to control head interface boards are different, so you do need one for a W7 control head.

Will

" And have some Micor chassis that people doing cop car or apparatus restorations might be wanting.
Lets talk... "

I have two Micor California Highway Patrol low band radios. No control heads. They do have channel elements.

Will

You may, depending the model of the charger, throttle it back so you do not croak the battery.

Will

d119 wrote:[
Putting both in the machine is a waste of money.

Why bastardize the MSF5000........

Will

I would NOT use the dammed R.I.C.K., WAY too many problems.

Buy the cables from MRE. (someone help with the correct site info.)

Will

I would be inspecting the cable for kinks and other deformations.

Will

I forgot to mention - I recall going through fleets adding resistors to vol pots to set min vol levels because people would leave them down. A somewhat futile exercise, but it made someone happy. We did that same thing at many dispatch consoles or remotes. And a Police dispatch on the fire radio re...

Will

Remember that Motorola numbered the RJ mic jacks backwards from the US RJ45, ect, standard. So does Kenwood.

Will

Well documented on Jeep and Dodge truck forums.

Will

An open circuit is what triggers the Emergency Alert.

Will

Add the 'programming' leads to your existing connector and another jack for your programming cable.

Will

The Transmitter coax cable connector is on the back of the R1225 chassis along with the power and 16 pin ACCY connectors.

The receiver antenna connector is on the front, along with the 'control head' connector.

Will

AND/OR setting as explained long ago.

Will

SteveC0625 wrote: COR (not CORE) is readily available at the accessory connector. It may require a minor programming change.

Motorola calls carrier detect RUS, receiver un squelch, No relays anymore...
Look for PL/DPL DET. An open collector transistor output. Pin 8.

Will

Welcome to the BatBoard Sir.

Will

Spectra mic cords will not solder well, they are the tinsel type.

Will

Is it really a R1225 or just a couple of Radius radios in the box.

When the R1225 is set for external so called controller it may not send repeat audio due to programming. So: step 1 read the radio and check the accessory potions settings.

Will

"Pushing in a S-record" requires realignment and calibration.

Will

Spectra A4 mid power UHF runs the siren without a DEK.

Will

Next step. try that radio with a standard control head pluged in.

And is the 'transmitting ' radio on the left side?

Will

I break each radio down and test them by them self's. They should be Maxtracs.

Look carefully at the board behind the front panel for moisture ect.

Will

Thank you Sir, a welcome addition to my personal library.

Will

We run our Maxtrac and Radius radios in station and repeater without the 'control head's. Just a jumper on the front connector to turn it on.

Will

You can get your radio "revived" but it takes flashing it. I send my 'bricks' to a fellow in Canada and they work just like new. I have to do a full alignment and calibration on them, because the tuning values are at default just like the factory radio before they do the alignment and cali...

Search found 6214 matches