Batboard

central150

Looking for a whored out s-rec for an xts3000 VHF model 3. Anyone help me out??

central150

I used the 19.60.5, it's a 4 meg so it would have went up to R16.00.01. When I read the radio with CPS, it shows the tuner version as 'unknown'. I've never seen that before.

central150

Jupt updated the firmware in my XTS2500 800. Now when I try and put it in service mode, I push the lower button 5 times, the radio beeps as if it will go into service mode, the screen goes blank as if the radio was turning off, then back on again. I've never seen this before. Anyone have anything li...

central150

Bump....anyone??

central150

Looking for an S-REC for an MTS2000 800mhz top display. (H01UCD6PW1BN) I need in the flashcode to have Smartzone and MDC options. (A whored out one would be nice too.)

Any help would be appreciated.

thanks,
-Tony

central150

Tony, I believe I ran into the same problem with an older XTS2500 (might of been a 1500). There was a secondary setting somewhere that I had to manipulate. I also had issues with my key not loading properly at first which caused me to be unable to change those settings. I will fire up the laptop an...

central150

KS4VT wrote:You have Q52 and Q53 in the radio and I believe there is a confilict with the Astro25 trunking and FPP wins as the dealer.

That's what I thought it was too. I have a VHF with the same flashcode and was able to choose either type 2 or Astro25 trunking.

central150

Hey gang, I have an XTS2500 800mhz. I'm trying to program in a P25 trunked system and I'm starting to get a little teed off. I have the system key, the flashcode for the radio is 5A1018-10178C-5, the HOST is R09.00.03 the DSP is R09.00.02 and it's a 4 Meg radio. When I'm in the Trunking System, it ...

central150

Hey gang, I have an XTS2500 800mhz. I'm trying to program in a P25 trunked system and I'm starting to get a little teed off. I have the system key, the flashcode for the radio is 5A1018-10178C-5, the HOST is R09.00.03 the DSP is R09.00.02 and it's a 4 Meg radio. When I'm in the Trunking System, it o...

central150

Remote speaker mic problem with an MT-1500 800mhz. New officer received a brand new MT-1500 from Motorola. We have tried several different speaker mics, all to no avail. I didn't see anything in the programming? Either the radio is the problem, or I am.. Any suggestions?

-Tony

central150

Looking for an S-Record for an XTS3000 800mhz model 3. A whored out one would be nice...

email: central150@gmail.com

thanks,
-Tony

central150

COM,

Thanks for the info. Do you know the part number for the 'serial programming cable'? I'm going to order that on Tuesday.

central150

Maybe I'm doing something wrong here. I'm trying to fix one of our Dept. CDM1550's with the EEPROM Error with 6.11.05. I get the option to 'Recover the radio with the default codeplug', I choose that option, click 'Ok' then it looks as if the program is working, then the CPS is "Not Responding'...

central150

I have read it... There is no MDC in it..

central150

And the flash is 000001-000000-9

central150

Ok. I have firmware version 5.44 in that puppy now.

central150

Ok...Anyone possibly know an approx. cost to add this option to an mts2000?

central150

I have an MTS2000 w/o MDC, and I would like it flashed in. Can my local MSS do this or do I have to send it to the depot, wherever it is now. And possibly an appox. cost...

-Tony

central150

a speaker? You mean a speaker mic?

central150

Read the radio, then click on "Radio Information", under the General Tab will be your Firmware Version in the radio.

central150

Building the hardware involved is not a problem (assuming you already have a RIB & cable for regular programming). You can find the info in the model specific pages on Batlabs: http://www.batlabs.com/htpro.html http://www.batlabs.com/images/hln9742.gif The trick is finding the firmware update p...

central150

I believe a RICK. The unit does have a duplexer attached, and the repeater controls at the top to turn off the repeater function and the setup button. I really haven't opened up the cabinet yet to look inside. But they are 2 M10's together in a small cabinet with "GR300" at the bottom. Not...

central150

The output on this thing is great, but when transmitting from a portable/mobile to the repeater, the input audio is crappy. It's really choppy and staticy. Any suggestions?

Tony

central150

Got it...thanks!!

central150

Ok...I tried that earlier, and when I used my portable radio in direct (155.760 114.

, it keyed the repeater.

central150

I have 2 M10's together, duplexer and all in a repeater set up that I purchased. These are vhf, and, as you know, single channel radios. I have a programming question. The Receive radio for the repeater, I program that with the frequency that I transmit on with my portables, and nothing in the TX si...

central150

my firmware version is 05.05.14 for the codeplugs. It may have to do with the CPS. I am using 06.04

central150

it is an LS+....my bad...

central150

If you program the button's function for, as appropriate, either "Cal Alert Member #1" (or #2, or #3), or "Sel Call Member #1" (or #2, or #3) it should do what you want. Obviously, the call that you want to access will have to be in the appropriate first, second, or third spot i...

central150

Ok..I got it working. Now, I would like to program one of the buttons as the call button to send out tones. it is programmed as radio call) As it is now, I have to hit the call button twice to get to the groups to page. We have a CDM1550 uhf here at the PD, when you press the call button, it goes ri...

central150

Could you send me the codeplug? central150@aol.com

thanks
Tony

central150

We have a back up CDM1550LS+ at our FD for back up paging in case our main radio goes down. I set the unit up to page out using Selective Call. What I want to do, and couldn't figure it out, is after I page the group, I want to be able to push the PTT button and broadcast my message. Now, if I push ...

central150

Make sure you have a good cable and rib, and the battery or other power source for the rib is good.

central150

thanks Todd.

central150

Is there anywhere on batlabs that can show us how to make one? Or does somone have a diagram??

Tony

central150

Does the XTS1500 use the same programming cable as the XTS2500? And we can't use the Jedi series cable on these radio's, correct?

Tony

central150

Pj wrote:Its been my experience that most people will yield the ROW in "curtosity" light states, depending on the area. More lights you have, better the chances.

You better get out of my way!! lol

-Tony

central150

Then really what is the point of having lights? Here in Ohio we run Red & Clear, and have the same priveleges and laws about running hot than the LEO's, fire engines, ambulances, ect.... Now sometimes it is a little hard to explain to vollies what "due regard" is, but I still operate ...

central150

Were not "emergency vehicles" as defined in Mass. General Laws.

central150

jmr3865 wrote:That is Kentucky state law: you must be OFF the roadway.

Massachusetts, volunteer/call firefighters use red lights, the law states that it is a courtsey light, vehicles do not have to pull over for you with it activated.

central150

Top display - 8405641V02 FLEX, Front Cover/Display Front display/no display - 8405310W04 FLEX, Front Cover/Display The front display/no display flex assemblies are the same, you just don't solder the connections in radios with no display. Todd Todd, does 8405641V02 actually come with the display an...

central150

Now I just need a Pro5150 to play around with.

central150

I just did it.... Dirty

central150

I have Ready Link....413-222-5299. Hit me up

central150

Woody_99 wrote:jistabout... try this link: http://www.freetranslation.com
and it will give you sometimes a fantastic translation and as in this case, an acceptable one, to help figure out what someone needs.

Тот вебсайт довольно прохладен...

Tony

central150

Crimestopper wrote:If you have a parts account contact your local ISM, and ask him to remove the restriction. It took some work, when I needed it done but now it is not a problem...

Steve
Crimestopper

I have an MOL account through our Fire Dept. What is an ISM??

Tony

central150

The REX kit comes with pretty much everything you need, except for the label, as not above. The one thing to be aware of, as with any Professional Series refurb kit, is that you have to deal with the accessory / audio flex, which is stuck to the case with a thin adhesive strip. It is possible to ge...

central150

SD70MAC wrote:The kit is REX4662 full keypad and you will have to also get the HT1250 label HLN9962.

SD70MAC out

I tried to get the HT1250 label via MOL, called them and said that it wasn't in my catalog, and I would have to order it from my nearest dealer. WTF is up with that?

Tony

central150

It's definetley an MDC burst. No one is keying up during their transmissions. Could it be that they are using say another brand of portable or mobile radio, Kenwood, with some kind of MDC add on? I know their motorcycle units use Kenwoods, not Moto's.

-Tony

central150

Yeah, it's kinda different.

Search found 563 matches

S-Rec

Re: XTS2500 Service Mode

XTS2500 Service Mode

Re: S-Rec needed

S-Rec needed

Re: XTS2500 Programming

Re: XTS2500 Programming

Re: XTS2500 Programming

XTS2500 Programming

MT-1500

XTS3000 S-Record needed

Re: The HT1250 EEPROM fix Secret

Re: The HT1250 EEPROM fix Secret

MTS2000 MDC

GR300 / M10 programming help

CDM1550 Programming Help

XTS1500

Re: say what?

Re: ht