Batboard

J_L_COHEN

Awsome Thanks Guys!,

J_L_COHEN

ok guys im in need of some expert help here, I have been reading the forums on astro stuff since 1030 pm and its now 330 am :o im new to the astro line and have rather become a big fan, but im not sure of all the flashcodes and such, i have learned quite alot by browsing the board looking for the ...

J_L_COHEN

hey guys is there any one out there that can convert my mII to A mIII? i had it done a long time ago from a guy in ok, but i have lost his number, i have all the parts to convert the radio

thanks

J_L_COHEN

Hello

Is there anybody in Ohio close to Zanesville That can program a mt2000?
Of courese there will be some cash involved

Thanks Jeffrey

J_L_COHEN

Thanks

Bad battery in the truck

should have guessed

Thanks Jeffrey

J_L_COHEN

hello all, I have a wierd issue with my cdm1250 vhf, I did some changes to a few pls and reprogramed, now when I tx on a certen channel it gives me this funny sound like a batt going dead on a ht1250 and then my mdc will key up, the radio seems to work ok both tx & rx I can't seem to find a setting ...

J_L_COHEN

hello, I know that it has been discused, but I need a Operators Manual for a Mt2000, or a list of what the icons on the display are for (ie the flashing square), and how to program the scan lists from the keypad.

thanks in advance
Jeffrey

J_L_COHEN

I looked at most of the search lists regardig the probliem, and i can't seem to find a answer can somebody tell me or point me,

i am trying to program the abc switch on a ht1000, I am in the program I see all the slections, I select the ones that I want, program into the radio, but they don't stay ...

J_L_COHEN

yep mine did the same thing,
the part # for the display is 5105385y57 cost 67.50, also when you change the display, be careful when you put the new one in, you can crack the lcd real easy

J_L_COHEN

hello all,
I need a parts break down list for my ht1550, does anybody have one or can point me it the direction of one.

Thanks
Jeffrey Cohen
Newton Twp Fire & Ems

J_L_COHEN

Hello,

I have a cdm enhanced mic # aarmn4026b, and I broke the clip off the RJ45 type connector, does mot sell just the connector or do I need to Purchase the whole cord set, If so is there a special part number.

Jeffrey

J_L_COHEN

which one are you looking for, the flat membrane type or the slide switch with flat membrane, or the slide switch with the raised buttons.

Jeffrey

J_L_COHEN

Thanks Jon that helped!

J_L_COHEN

Hello All I am in need of a vhf codeplug for a ht1550, I am trying so set up mdc sig, but can't seem to get it to decode, just want to see what the defult settings are.

Thanks Jeffrey

J_L_COHEN

Hi guys this one has me stumped, I have looked at all the posts in the search, but I can't seem to find a correct answer so I am asking the experts, I am trying to set up mdc from a gp300 to a pro9150, I have set up numorus ht1250's and they work fine, but this radio just won't decode I have kept ...

J_L_COHEN

hi guys,

I looked for a link in the search menu but I did not find what I need so it's time to ask the experts

I want to build a repeater that I can use for my business, I have a tower that I can use but I don't know what type of equipment I need.
can I use 2 mobile radios and a rick and a ...

J_L_COHEN

Chuck's right those things are "tank proof" we use them on our department, we have the sentralok verison on our medics and engines, in order to gain access to the key we must radio dispatch, tell them what truck you are on and your FD unit # and then they will send out the dtmf for that truck and ...

J_L_COHEN

thanks for the info

jeffrey

J_L_COHEN

hi can anybody tell me if this ht is still under warranty
model H25RDF9AA5
ser 749TZW6377

thanks jeffrey

J_L_COHEN

Yep, I have a HNN9010AR Intrinsically Safe, date 10-2003 and a HNN9009a standard battery, date 1-2004 and out of the two batterys the new battery will out last the IS one by 2-3 hours, I thought it had something to do with the Intrinsically Safe option.

Jeffrey
Newton Twp Fire & Ems

J_L_COHEN

Hi guys, sorry this is off topic, but I need a program cable for a Maxon
sp-130u2. if any body can point me in the direction of a digram to build one or a dealer who sells them that would be great.

Jeffrey

J_L_COHEN

no, it's the tk 1.6. the option # 4 is for ht600-p200,

if I made the cable using just the 3 wires as described here on the board, and i can read and write to the radio, I should be able to do the same with the TK ?. is there other pins needed to do this other than 3 described.

j

J_L_COHEN

hi I am trying to change my p200 from 2 ch to 6ch, I have tk v1.60, when I try to convert the radio, I get a message like this:
SERIAL BUS ERROR, CHECK RADIO CABLES ECT, so I changed the com ports many times, but is still will not go,
I can program the radio fine from this computer with the cable ...

J_L_COHEN

thanks for the reply, you don't happen to have any of those boards ?

jeffrey

J_L_COHEN

hi i have 3 sprit pro + su21d radios and i would like to have pl board for these radios, does any body have a motorola part # or a dealer i could purchase them from

thanks jeffrey

J_L_COHEN

i don't know if this has any thing to do with it but, the maxtrac was a upgraded from a 2 ch 5 pin connector to a 32 ch 16 pin with signaling

J_L_COHEN

they are constant power, i just use the on off switch

J_L_COHEN

ok this is one for all you techs and people with years of installs,
3 weeks ago I had my local moto dealer install a rick in my truck for crossband use cdm-vhf to a maxtrac lowband, every ting works great except I have a enhanced mic on my cdm (RMN4026) now when i turn the cdm off the back light on ...

J_L_COHEN

this is just a general question, we are a volunteer fire dept and we have a problem with portable radios disapearing, how does every body mark there radios, do you use paint, engraving, colored cases, ect. we are about to purchase 30 new cp200 radios and the cheif wanted to get some ideas on how to ...

J_L_COHEN

hi guys im trying to figure this out but no luck, on my gp300 there was a setting called signaling squelch, so you would hear nothing on that channel unless you push the mon button or our tones go off, but i can not find it in the programing for a 1550 (r6.00) what i am trying to do is put a second ...

J_L_COHEN

Hi does anybody off hand know the part # for a ht 1250/1550 series vehicle charger, and where I might find a pic

thanks jeffrey

J_L_COHEN

hi
this has been asked before and i think i have found the answer, but the folks on this board will know, the p200 can be modified to 6 ch, will not scan, but you can do QC-II with limited tones?

and can any body tell me if i can still purchase housings for a p200, or does any body have 6 sets to ...

J_L_COHEN

Hi can any one tell me if a p200 uhf 2 ch can be upgraded to a 4-6 ch radio

jeffrey

J_L_COHEN

HI I have put a plug on a pa 300 but it was a real pain, what model do you have, and does it have a black or silver face, and does it have hi-lo or piercer

jeffrey

J_L_COHEN

hi monty,

you stated that you would need a test jig? ok im lost what is this and where can i get one, i need to change the crystals in about 3-4 radios, is that sometihing that i sould be able to do or should i take it to a mrss

thanks jeffrey

J_L_COHEN

hooknladder

how much are you asking for the radio

jeffrey

J_L_COHEN

hi can any body tell me where i can buy uhf crystals for a p50

thanks jeffrey

J_L_COHEN

thanks guys, that helped where can i find a pl list for the switches, that will tell me in which position the switch is in equals the pl tone (if that makes sence

)

jeffrey

J_L_COHEN

hi can any one tell me if this p50 radio is uhf H44GNU3120AN,
and was the p50 seires radio software programed or was it a crystal type radio

thanks jeffrey

J_L_COHEN

Matt,

yep, when some bodys tones drop from dispatch the final tx, rx for these towers all are on the same lowband freq.

our tower is only 45watts, and about 15 miles away from one of the other towers and 5 miles from the other. but if i stand at our station and change channels to the other tower i ...

J_L_COHEN

Jim202

let me go into more detail of what we have, I may have mis led some (sorry)

about 4 yrs ago our department carried moto sp50 lowband radios 33.98
of corse they were bulky and the antena was a pain (foot long) so in the wisdom of our cheif ect we decided that we would go to a vhf radio (p ...

J_L_COHEN

Jim,

Yes the signal is very strong and clear, I also checked my tones to make sure that they were the correct setting and it was correct, i was close to one of the other towers today and we had a run, my maxtrac lowband in the truck went off for our tones but my portable (on that tower) did not ...

J_L_COHEN

this is a question regarding the recieving of QC-II tones
I have a pro 9150 v3.1.03
what i am trying to do i don't even know if this is possable it should be but hey, in our county we have three towers (3 diff vol fd's) Newton, Harrison, Falls, which talk to our county fire dispatch, 3 diffrent ...

J_L_COHEN

MATT

sorry, no we currently do not use mdc, but our cheif would like us to have it, I was saying that in the city of Zanesville the fd went to mdc id's and our cheif thinks that is a great idea

jeffrey

J_L_COHEN

Ok it another mdc question

First I looked in the mdc topic but it does not answer my question well here it goes

I have a pro9150,cdm1250,gp300 all with mdc set up
our local fd has mdc signaling set up on there radios so when a radio keys up it shows the name ID of the radio (ie engine 2), I would ...

J_L_COHEN

HI Will

Can you also get me some info on your box

Jeffrey
[email protected]

J_L_COHEN

Hi Dave,

No it did not work it will only allow 16 ch per zone, I have spent the last two days trying, so I guess i will make it do

thanks for your help

jeffrey

J_L_COHEN

thanks, i could not find it

jeffrey

J_L_COHEN

Hi

is there a web site or a chart that tells you the manafacture date of a radio
i would like to know for a warranty question

m pro 9150 sn # 841taw1522

and does any know what the latest verison # is out this one is r03.01.03

thakx
Jeffrey
Newton Twp Fire & Ems

J_L_COHEN

Hey guys tnankx for the help

Search found 71 matches

Re: xts5k and 2k flashcode questions

xts5k and 2k flashcode questions

xts mod II to M III convert

Radio Programing Wanted mt2000

strange cdm issue chrip

Needed Mt2000 Operators Manual

ht1000 abc switch program question

ht1550 part list needed

cdm enhanced mic

HT1550 CODEPLUG NEEDED

PRO9150 MDC

newbie repeater help

ht1250 warranty

OT SORRY PROGRAM CABLE FOR MAXON

p200 2-6 ch

sprit pl board

mic stays on with a cdm1250 and rick

MARKING RADIOS

HT1550XLS SIGINALING SQUELCH

Ht series mobile charger

p200

p200

p50 crystrals

MOTOROLA P50

QC-II & Multiple Towers

MDC SIGNALING

HT 1550 PRO 9150 programing

M Date code

HT 1550 PRO 9150 programing