Batboard

smile@2006

You can upgrade & downgrade firmware with proper tool.
Such as eprom programmer.

smile@2006

You can convert codeplug file to file.0

Ony need one minute.

smile@2006

The radio have checksum error.
So it can't clone.
Use latest cps to fix this problem.

Or use waris labtool to do job.

smile@2006

Simple trick to fix it.
Equipment:
- Radio Interface Box, P/N RLN4008
- Programming/test cable, P/N RKN4074A or RIBless programming cable, P/N RKN4075A
- Flash adapter, P/N HLN9742.
- Good radio ( master ).
- Bad radio ( slave ).

Procedure:
1. Start the Firmware Kit.
2. Connect a fully charged ...

smile@2006

Use CPS R05.09 or above

smile@2006

Hello,
Load file codeplug the same radio model number, then write to the radio.

Program screen will appear as shown below:

Select:
Recovery the radio with the default codeplug.

smile@2006

Hi,
Use this cps to fix your radio.

===============================================================
Professional Radio - Customer Programming Software R06.11.05
================================================================

Enhancements in this release:
---------------------
N/A

Fixed ...

smile@2006

You must take the Alpha Tuner software from MOL.
Read all the parameters one by one, without written to the radio.

If it still fails, read all the parameters of a normal radio, save in the format *. eep
Then write the data (*. eep) radio to the problem earlier.

Happy trying, hopefully ...

smile@2006

Pro Radio Model Number

Freq. Band:
B = Low Band R1 (29.7- 42.0 MHz)
C = Low Band R2 (35.0-50.0 MHz)
E = 300R1 (300-350MHz)
K = VHF (136-174MHz)
R = UHF1 (403-470MHz)
S = UHF2 (450-527MHz)
U = 800 MHz (806-824) (851-869MHz)

Power Level:
C = 2.5W
D = 4-5W
E = 6W

Physical Packages:
C = Non ...

smile@2006

clueless2009 wrote:Thanks, but do you know what the correct CPS is called that I will need?

ELP cps Part# HVN6053F

smile@2006

Does Motorola sell a RSS User's guide for the XTS2500? What would be the PN and cost from M?

Thanks

Readme file:

===============================================
ASTRO 25 Portable CPS R12.00.00
===============================================
- VISTA with Service Pack 1 is now a supported ...

smile@2006

ProRadio Latest Version R06.10.04:

================================================================
Professional Radio - Customer Programming Software R06.10.04
================================================================

Enhancements in this release:
---------------------
N/A

Fixed ...

smile@2006

The PM400 mobile two-way radio is perfect for new two-way radio users, small organizations, and firms that want an affordable solution with a maximum number features. It offers 64-channel operation, innovative LTR trunking capability and option board expandability.

Features:
Innovative LTR ...

smile@2006

It's hardware problem,
Resolder IC Flashrom (by hot blower solder).
or replace new IC Flashrom, go to www.atmel.com for type it.

smile@2006

[quote="bulletproof-791"]i have cps entry level pro. radio cps R02.02.00 and i was told that i can use it tp prog moto: ct150 ?
when i do read it it will show reading radio and then ERROR 4-1379...

Use elp cps R02.03.00 or later.
This radio newer then cps version.

smile@2006

Hi there,

How can i find out what frequency my GP388 is. (vhf uhf)

Its not listed on batlabs.com!!

Thanks

GP388 is EMEA region, like EX600 (LA) or GP338Plus (AZ).

Example:
AZH38RDH9AA6 = GP338Plus UHF 403-470MHz 128Ch
AZH38KDH9AA6 = GP338Plus VHF 136-174MHz 128Ch
AZH38SDH9AA6 = GP338Plus UHF ...

smile@2006

Does anyone know if the radio's memory (EEPROM) size on a CDM750 is, say, that of the same capacity as a CDM1250 or a CDM1550? I've searched but could not find an answer, and unfortunately do not have a '750 handy to toy with.

Thanks
Memory size of CDM750/1250/1550 is 16k bytes.
Dependent year ...

smile@2006

Looking for somebody who can repair and align XTS5000 with ABC123 serial#.

Use tuner software, go to MOL.
.....

===============================================================
ASTRO 25 Tuner R05.04.00
===============================================================

This new version of the Tuner ...

smile@2006

Disbale password & all region support CPS R05.07 (AZ) Region:

Offset 1155905 7505 to 9090

Offset 2045867 7505 to 9090

Offset 22DD75 7505 to 9090

smile@2006

New version:
R02.03.00 HVN9065 (MTX8250)
R02.03.00 GMVN4001/GMV4002 (GP580)

Contatc M dealer

smile@2006

Please check thread for dissable password...

smile@2006
Indonesia

smile@2006

Hello all,

I have possible problewwith a CD1M1250 low band. It is wire to battery power and to ignition sense. It is programmed to follow ingnition sense only with no other pins connected or programmed. The problem I am having is that each time the ignition is turned off then back on the radio ...

smile@2006

Use winHex or HexWorkshop to load cps.exe
Change instruction JNZ to JZ to dissable password option.

smile@2006
AZ AA LA MD FD

smile@2006

So, you can change setup.xxx from LA to AA region or vice versa.
With the tip, I can change setup full version CPS AZ to:
LA
MD
FD
AA
or vice versa.

smile@2006
AZ-AA-LA-FD-MD
HUMAS@%&
INDONESIA

smile@2006

Hi,
Disassembler cps,
change optinon JNZ to JE to disable password.
or,
Delete Dialog Password from cps structure.

Successfully to carck:
CPS R06.07.04-AZ (GP328/GP338)
CPS ELP R02.01.02-AZ (GP308)
CPS ELM R05.05-AZ (GM3188/GM3688/GP3188/GP3688).

smile@2006
AZ-AA-LA-MD-FD
HUMAS@%&
INDONESIA

smile@2006

Any idea to edit eeprom R100 with Universal Eprom Programmer?
I have rx & tx eeprom, but don't know address of frequency.

smile@2006

smile@2006

Any idea to edit Rx Tx EEPROM Repeater R100?
I have hex file from rx & tx EEPROM.

smile@2006

Load archieve codeplug model M33GMC20DAA,
then clone to the gm300 with error 58.
Try and try again until success.

e=mc2

smile@2006

24c16 is SMD case SOIC8.
(covered with paper insulated).
Remove it from RF Board (under keypad board).
Then replace with new eeprom.
For eeprom detail go to http://www.atmel.com

e=mc2

smile@2006

smile@2006

Resolder Flashrom AT49LV001NT TSOP32 case,
or EEPROM AT25128 or AT25640 SOIC8 case.

smile@2006

smile@2006

Firmware at flashrom caused dead radio.
Remove flashrom from the board,
than replace with new flahsrom (AT49...).
You must write down firmware into flashrom use universal eprom programmer (ALL 11P, Brightek, TOP, EasyPro, etc).
Only 25 minuts....

:D :D :D
smile@2006
:D :D :D

AZ LA MD FD AA ...

smile@2006

Usually 2nd X'tal 44.645MHz is damaged.
Inject 555KHz near IF test point, you will receive the signal.
Please remove X'tal and replace it.

smile@2006
"AZLAMDFD"

smile@2006

I use AT49BV001-55TI to replace AT49LV001NT-70TI for gp328/gp338/gp308 (Asia region) still no power up.
Before replace it, i read all data from AT49LV001NT-70TI,
then write to AT49BV001-55TI.
Use EasyPro 80B to read & write flash room.

smile@2006

Can AT49LV001NT-70TI replace with AT49BV001-55TI?

smile@2006

Use Interface Tester software to check it.
If you need it please pm.

------------------------

AZ-LA-MD-AA-FD

smile@2006

New info...
Dissable password CPS R06.06.00
Change to BDxx from 75xx
address: 0036ABCA

@MAHSU%

smile@2006

Ed wrote:
It's possible to blank the serial number using LABflashgrade, and use ProRadioTuner to put ANY serialnumber back in the radio.

--------------------------------------------------------------------
Thank's for all, now I can change SN with ProRadio Tuner (modify).

:D :D :D ...

smile@2006

I buy used GP338 from ebay,
model AZP25RDH9AA5
the sn is 1234567890.

Thank's for all, i will send it to /\/\

---------------

--------------

smile@2006

How to change the Serial Number ProRadio (HT750/1250/CDM, etc)?
Any idea for it?

AZAALAMDFD

smile@2006

For CPS R06.05.00:
Address of dissable password is 00452ABC (Hex offset of *.exe).
Change 75xx to FDxx
------------------------------------------

@MAHSU%

smile@2006

For safety, use +5Volt DC.
If use +12Volt DC you must becarefull...!!!

----------------------------------------------------------------------
Use Positif Regulator IC type 7805 or 78L05 to convert +5V.
-----------------------------------------------------------------------

smile@2006

Inject +5Volt DC to IGNITION SENSE pin.
Then turn on the radio.

--------------------------

smile@2006

I have #8264934B01 Waris VA Firmware.
What can I do to flashgrade my gp338?

smile@2006

You can get it from:
http://www.myradiomall.com
or
http://www.wiscomm.com

------------------------

smile@2006

PTX760 & PTX700 can't read/write with CPS R06.xx.xx-AZ.
You must use CPS Prof. Trunking Radio R05.xx.xx-AZ or later.

-------------------

smile@2006

Trick to dissable password:
1). Dis-assembler *.exe file to make *.txt file.
2). Locate StringData "INCORRECT PASSWORD" in *.txt
3). Locate 74xx "INCORRECT PASSWORD".
4). Write to paper the address of 74xx.
5). Open *.exe with HexWorkshop.
6). Change command JNE (Jump If Not Equal) to JMP ...

smile@2006

I have 4pcs GP338 R05.xx.xx VHF still EEPROM HW ERROR.
Also try fix with falshgrade R05.xx.xx don't work.
Any idea to fix it?

Search found 47 matches

Re: Codeplug need

Re: ATS2500 Problem after wrote with Codeplug

Re: Anyone ever seen this Model error before?

Re: HT1250 firmware update gone bad

Re: CPS R05.07

Re: Motorola CDM-750 error

Re: Motorola CDM-750 error

Re: CP125 EEP ERR - Any ideas?

Re: Want to check a HT1250 Model Number

Re: CT-450 CT-250 CT-150

Re: Motorola CPS 12 HELP...

Re: pro radio cps latest version

Re: pm400 and cm300 diff?

Re: GM360 dead

Re: error code 4-1379 what does it mean

Re: GP388 FREQUENCY

Re: CDM750 memory (EEPROM) size?

Re: Anybody repair radios with ABC123 serial #?

Re: Commercial Series Region Hack

Re: MTX (Waris) Programming Software

Re: OFFSET FOR ELM ELP EP450 CPS

Re: CDM 1250 Power up

Re: Password Reset ?

Disable Password CDM

R100 Frequency edit

HEX address rx tx R100

Cloning Codeplug

Change Serial Number ProRadio...