Users may not create topics, posts, or private messages containing or relating to the following material (especially pertaining to Motorola copyrighted software, unless you want Motorola to come along and shut this site down):

  • Listing for sale or trade of, or links to sites offering for sale or trade of, or giving away, Radio
    Service Software (RSS) or Customer Programming Software (CPS)
  • Profanity, pornography, defamation, or slanderous remarks directed towards any individual or entity
  • Commercial advertising (except in the Batboard Vendors forum, as approved by the Admin/Mod Staff)
  • Any other items which may be deemed as offensive

If any topics, posts, or private messages containing or relating to the aforementioned material are brought to the attention of the Admin/Mod Staff, they will be deleted.

Additional FAQ items appear here in Forum Rules. Please review them for posting guidelines and further clarification.

HSN4035C - SPEAKER KIT MOBILE

The General forum is where users can discuss any topic regarding Motorola communications equipment - hardware, software, etc. There are also several focused forums on this board, so please take the time to ensure that your questions doesn't fall into one of those categories before posting here!

Moderator: Queue Moderator

User avatar
bburzycki
New User
Posts: 5
Joined: Fri Jan 15, 2010 11:04 pm
Location: California / Nevada
Contact:

HSN4035C - SPEAKER KIT MOBILE

Postby bburzycki » Sun Sep 15, 2013 9:57 pm

So it seems I need a bit of help to understand why this specific speaker will trigger only on specific types of outputs.

We have been asked by a customer to integrate this speaker to rebroadcast from a laptop computer. No matter what we do it seems the built in amp will not trigger based on the output of the computer.

Does anyone have any ideas the reason for this?

I assume we are missing something simple and just need to be reminded what..

Do we need to pre-amp the output? Before sending it to the speaker? That just seems strange to me...

Thanks

Will
Posts: 6821
Joined: Tue Sep 04, 2001 4:00 pm

Re: HSN4035C - SPEAKER KIT MOBILE

Postby Will » Mon Sep 16, 2013 1:51 pm

You can use one of the Motorola speakers with the built in amplifier. These will take the line level audio from your computer and drive the speaker. You will need 13 volts at 2 amps to power the speaker amp.


You can also use a 600 to 600 ohm transformer and feed the house PA system.

There are many ways to do this.

RFguy
Posts: 1081
Joined: Wed Dec 21, 2005 6:17 am

Re: HSN4035C - SPEAKER KIT MOBILE

Postby RFguy » Mon Sep 16, 2013 2:39 pm

I think the HSN4035C is an amplified speaker.

It's looking for speaker level audio, not line level audio. You will probably need a pre-amp to run it from a computer line output.

User avatar
bburzycki
New User
Posts: 5
Joined: Fri Jan 15, 2010 11:04 pm
Location: California / Nevada
Contact:

Re: HSN4035C - SPEAKER KIT MOBILE

Postby bburzycki » Tue Sep 17, 2013 8:45 pm

That was my fear - any suggestions on a pre-amp?

Will
Posts: 6821
Joined: Tue Sep 04, 2001 4:00 pm

Re: HSN4035C - SPEAKER KIT MOBILE

Postby Will » Thu Sep 19, 2013 11:34 am

bburzycki wrote:That was my fear - any suggestions on a pre-amp?


You do not need a pre-amp. If I can get the diagram of the amped speaker, there is a load resistor on the input you remove. Just do not have the diagram on the HSN4035.


Return to “General Motorola Solutions & Legacy Radio Discussion”

Who is online

Users browsing this forum: Bing [Bot], jmfirefighter20, Yahoo [Bot] and 3 guests