Vehicle Repeater 2 Radios

The General forum is where users can discuss any topic regarding Motorola communications equipment - hardware, software, etc. There are also several focused forums on this board, so please take the time to ensure that your questions doesn't fall into one of those categories before posting here!

Moderator: Queue Moderator

Post Reply
User avatar
tuckerm
Posts: 561
Joined: Thu Jun 10, 2010 12:21 pm

Vehicle Repeater 2 Radios

Post by tuckerm »

Anyone have a suggestions for a vehicle repeater utilizing two XTL 5000s? Obviously one radio is the master so when I transmit I'd want the audio to go out there but I'd like both radios' RX traffic to go to the VRS simultaneously.

I'm currently using a Pyramid SVR-200 and am thinking of splicing two cables into one....
Schrodinger's Radio: It is simultaneously too loud and too quiet, but you will never know which until someone transmits.
User avatar
Bill_G
Posts: 3087
Joined: Thu Sep 17, 2009 5:00 am

Re: Vehicle Repeater 2 Radios

Post by Bill_G »

Why would you want that? That should be an invalid state. The first to receive causes the other to transmit. ie: not receive. So, there would not be a second receive to get simultaneously. It's not present.
motorola_otaku
Posts: 1854
Joined: Tue Jan 13, 2004 7:03 am

Re: Vehicle Repeater 2 Radios

Post by motorola_otaku »

I'm interested in your usage scenario too. It sounds like you might be better off using a portable interop gateway and three mobile radios.
User avatar
tuckerm
Posts: 561
Joined: Thu Jun 10, 2010 12:21 pm

Re: Vehicle Repeater 2 Radios

Post by tuckerm »

I have a "Law" and a "Fire" radio in my truck. Portable reception in my county doesn't exist. I use the Pyramid when I'm out of my vehicle. I'd like to monitor both radios through the VRS but only be able to transmit on the Master radio.

I know the X10DR can do it but everyone I know that uses those have quite a bit of range issues.
Schrodinger's Radio: It is simultaneously too loud and too quiet, but you will never know which until someone transmits.
User avatar
Bill_G
Posts: 3087
Joined: Thu Sep 17, 2009 5:00 am

Re: Vehicle Repeater 2 Radios

Post by Bill_G »

Open up the harness to the radio that can't be heard, and add a spkr.
User avatar
NSPD
Posts: 1626
Joined: Sun Aug 04, 2002 4:52 pm
What radios do you own?: Motorola FR50!

Re: Vehicle Repeater 2 Radios

Post by NSPD »

I would like to have this too. Pyramid makes a harness for the Kenwood NX-5000 mobiles allowing you to connect 3 mobiles to one VRS. Shame they don’t have it for the XTL.
Jake
User avatar
Bigred
Posts: 101
Joined: Mon Apr 14, 2008 7:08 pm
What radios do you own?: Junk that comes and goes...

Re: Vehicle Repeater 2 Radios

Post by Bigred »

motorola_otaku wrote:I'm interested in your usage scenario too. It sounds like you might be better off using a portable interop gateway and three mobile radios.
Cleanest way to go. Could do 2 XTL's and the SVR if it compatible with the gateway.

Down and dirty you could probably combine the RX audio (with caps in-line for safety) and get away with it but it would be nicer with a simple mixer to drive the TX. The COR from the XTL's can be diode or'ed together so either will trip the SVR's PTT.

If both radios are receiving at once you'll have garbage on your portable but I think you know that.
Lots and lots of watts...
Jim202
Posts: 3610
Joined: Sun Sep 09, 2001 4:00 pm

Re: Vehicle Repeater 2 Radios

Post by Jim202 »

The use of an interop gateway is a possibility. But the keying of your link to a portable will only get the first radio with receive audio. When that first radio stops receiving, then the second radio will have the ability to key the link. Only one audio path will be active at any point in time.

If your looking to "and" the audio of both radios to allow them to both be active at the same time, you won't be able to use a normal interop gateway. They are not normally designed to do that.
User avatar
syntor9k
New User
Posts: 68
Joined: Sun Dec 04, 2016 8:44 pm
What radios do you own?: Syntor X9000, Spectras, EFJ...

Re: Vehicle Repeater 2 Radios

Post by syntor9k »

A weird Idea maybe. Idea better if your a HAM too...

Use two VRS one on VHF one on UHF (revers of the radio connected). To receive them at teh same time. Use a HAM duel band, duel receive, HT (since there is no commercial radio's that do this) - Or use two commercial HT. This would require effort to keep the VHF and VHF VRS and UHF and UHF VRS out of each other. Keep antenna far as possible, use maximum frequency separation as well. If it had to work. Add notch bottles on the VRS antenna for the same band interfer (for example if the VHF radio was likely to transmit on 153.5, 155.0, 156.0, add notches for them (like a repeater has)).
motorola_otaku
Posts: 1854
Joined: Tue Jan 13, 2004 7:03 am

Re: Vehicle Repeater 2 Radios

Post by motorola_otaku »

tuckerm wrote:I have a "Law" and a "Fire" radio in my truck. Portable reception in my county doesn't exist. I use the Pyramid when I'm out of my vehicle. I'd like to monitor both radios through the VRS but only be able to transmit on the Master radio.

I know the X10DR can do it but everyone I know that uses those have quite a bit of range issues.
Gotcha. SOP in that case would be two VRSes and scan on the portable, with PTT and scan priority set to the "master" freq.

What you are trying to do could be homebrewed but you'd need something to mux the mobile to VRS audio (possibly something from http://www.rdlnet.com/series.php?series=13 ) as well as a way to combine COR to VRS PTT logic without damaging either radio's COR output.
User avatar
tuckerm
Posts: 561
Joined: Thu Jun 10, 2010 12:21 pm

Re: Vehicle Repeater 2 Radios

Post by tuckerm »

I'm working with Pyramid with a "Frankenstein" cable. I think it'll work but I have to change out my Mid Power XTL to a High Power.
Schrodinger's Radio: It is simultaneously too loud and too quiet, but you will never know which until someone transmits.
Jim202
Posts: 3610
Joined: Sun Sep 09, 2001 4:00 pm

Re: Vehicle Repeater 2 Radios

Post by Jim202 »

tuckerm wrote:I'm working with Pyramid with a "Frankenstein" cable. I think it'll work but I have to change out my Mid Power XTL to a High Power.
Not sure why you would have to go to a high powered XTL.. The mid power has the same connections on the accessory connector. It's just not a DB25 connector on a remote mount. The rear accessory connector may require you to set some software settings to obtain what control or signal or audio your looking for. These radios also have gain settings that might have to be set to obtain the needed audio levels.

I use to interface a software driven gateway to these radios all the time. Not even sure how many I did over the 10 years I worked for the company that made the gateways. But it was a good number of them.
User avatar
tuckerm
Posts: 561
Joined: Thu Jun 10, 2010 12:21 pm

Re: Vehicle Repeater 2 Radios

Post by tuckerm »

I have a High powered XTL now with two High Powered cables. I don't have any mid power cables to experiment with.
Schrodinger's Radio: It is simultaneously too loud and too quiet, but you will never know which until someone transmits.
Jim202
Posts: 3610
Joined: Sun Sep 09, 2001 4:00 pm

Re: Vehicle Repeater 2 Radios

Post by Jim202 »

tuckerm wrote:I have a High powered XTL now with two High Powered cables. I don't have any mid power cables to experiment with.


If you have the pins for the mid power accessory connector, you can make your own connections. The pins are available from Mouser, but I don't have the part numbers. They have been posted on this site a couple of times, so it should not take much searching here to find the information. A crimping tool for that style pins is also a help.

The Pyramid vehicle repeater is a decent choice. But it helps if you have the ability to make changes to it's operation and gain settings.

Jim
dfc2
Posts: 360
Joined: Sun Mar 10, 2002 4:00 pm

Re: Vehicle Repeater 2 Radios

Post by dfc2 »

OK, my $0.02.


Try using 2 Pyramid repeaters, on different freq's. figure out the separation in distance or freq to allow both to work low power.... then have your portable set up scan the 2nd channel, without allowing it to talk back to the repeater. so it monitors ch 1, and scans ch 2.... but talk back is ch 1 only...


DFC2
dfc2
Posts: 360
Joined: Sun Mar 10, 2002 4:00 pm

Re: Vehicle Repeater 2 Radios

Post by dfc2 »

Th eonly other option I can think of is to have a duel band radio (expensive) with a single pyramid... Ohio State patrol used a setup like this for years.
User avatar
tuckerm
Posts: 561
Joined: Thu Jun 10, 2010 12:21 pm

Re: Vehicle Repeater 2 Radios

Post by tuckerm »

Just an update to this. Pyramid support pointed me in the right direction. I made a Y cable with appropriate items to prevent blowing the radios up and only one transmitting. Both radios audio will come out the VRS simultaneously and when I transmit Radio #1 keys up. It works out great.
Schrodinger's Radio: It is simultaneously too loud and too quiet, but you will never know which until someone transmits.
User avatar
abbylind
Posts: 527
Joined: Mon Nov 05, 2001 4:00 pm
What radios do you own?: What dont I own?

Re: Vehicle Repeater 2 Radios

Post by abbylind »

Harris Orions and M7100s can put 2 radios together with one control head. Mating the Pyramid shouldnt be too difficult in that mode.
Glad you got it worked out for your XTLs
wd9cms
Posts: 189
Joined: Sun Oct 06, 2002 10:29 am

Re: Vehicle Repeater 2 Radios

Post by wd9cms »

I am interested in how you built the cable..can you supply the schematic diagram and how you isolated audio,cor and ptt?

Thanks,

Bill
Bill, WD9CMS
444.775 PL131.8/NAC293
927.900 PL131.9/NAC293
User avatar
tuckerm
Posts: 561
Joined: Thu Jun 10, 2010 12:21 pm

Re: Vehicle Repeater 2 Radios

Post by tuckerm »

I wish I saved the email from Pyramid. I ended up getting a a few serial cables and making a Y cable that came off the Pyramid smart cables. Radio 1 I left the cabling as is and Radio 2 I only taped the RX Filter audio and the activity pins. Used Rectifier Diodes and Capacitors to prevent audio and voltage flowing back into the radios. This allowed transmit audio to go to one radio and not both and allowed RX audio to flow into the Pyramid and not into the radios.
Schrodinger's Radio: It is simultaneously too loud and too quiet, but you will never know which until someone transmits.
Post Reply

Return to “General Motorola Solutions & Legacy Radio Discussion”