Users may not create topics, posts, or private messages containing or relating to the following material (especially pertaining to Motorola copyrighted software, unless you want Motorola to come along and shut this site down):

  • Listing for sale or trade of, or links to sites offering for sale or trade of, or giving away, Radio
    Service Software (RSS) or Customer Programming Software (CPS)
  • Profanity, pornography, defamation, or slanderous remarks directed towards any individual or entity
  • Commercial advertising (except in the Batboard Vendors forum, as approved by the Admin/Mod Staff)
  • Any other items which may be deemed as offensive

If any topics, posts, or private messages containing or relating to the aforementioned material are brought to the attention of the Admin/Mod Staff, they will be deleted.

Additional FAQ items appear here in Forum Rules. Please review them for posting guidelines and further clarification.

Motorola Quantar SCM

This forum is dedicated to discussions pertaining specifically to the Motorola ASTRO line of radios (those that use VSELP/IMBE/AMBE), including using digital modulation, digital programming, FlashPort upgrades, etc. If you have general questions please use the General or Programming forums.

Moderator: Queue Moderator

vanderau
New User
Posts: 1
Joined: Wed Feb 04, 2009 8:36 pm
What radios do you own?: Tait TM9155, Motorola Quantar

Motorola Quantar SCM

Postby vanderau » Wed May 20, 2015 6:17 am

Hello:

A couple of questions:

1. Can a SCM with V.24 port, from a P25 UHF Quantar repeater be swapped into a P25 VHF Quantar repeater, whose SCM didn't have a V.24 port, and the old VHF code plug written into the replacement SCM, and the repeater work "plug-and-play"?

2. I cannot figure out why my P25 repeater is not repeating supplementary data messages, like call alert (page) and unit call. These messages pass between radios correctly when the radios are in talk-around mode, but when they revert to repeater mode, they appear to not be being repeated. I never see a blip of the red transmit LED and the target radio never receives the call alert or unit call invite. IMBE voice repeats just fine. Any hints where to look to rectify this?

Thank you.

MattSR
Posts: 760
Joined: Mon Apr 21, 2003 10:00 pm

Re: Motorola Quantar SCM

Postby MattSR » Thu May 21, 2015 1:44 am

vanderau,

The V.24 port isn't part of the SCM. The V.24 port attaches to the Wireline card which sits next to the SCM module. You can swap the wireline card + V.24 board from your UHF Quantar into your VHF one, then read the VHF codeplug, enable the V.24 card, and write the codeplug back again.

Check your firmware versions,and also does the repeater key up when you send a page or call alert? You can see the Quantar key up and also transmit the digital 'tail' during the hang time/drop out delay. I have a few Quantars set up on 70cm and these work fine for call and page alerts.

Cheers,
Matt

User avatar
Astro Spectra
Posts: 609
Joined: Sat Sep 22, 2001 4:00 pm

Re: Motorola Quantar SCM

Postby Astro Spectra » Sat May 23, 2015 11:34 am

I assume you have RDLAP enabled? Also early firmware versions didn't handle data packets well.

Koniec12
New User
Posts: 1
Joined: Mon May 25, 2015 4:43 am

Re: Motorola Quantar SCM

Postby Koniec12 » Mon May 25, 2015 4:46 am

Is it possible to update really old firmware at ones?

MattSR
Posts: 760
Joined: Mon Apr 21, 2003 10:00 pm

Re: Motorola Quantar SCM

Postby MattSR » Thu Jun 25, 2015 5:59 pm

Yep, there's a couple of ways to get around it.


Return to “Legacy Batboard Motorola ASTRO (VSELP/IMBE/AMBE) Equipment Forum”

Who is online

Users browsing this forum: No registered users and 1 guest