I'm working on a R2001A service monitor that I had some brightness issues with. Replaced the zener diode with a new one, but in the process of moving the boards (There are three in in the R2001A HV supply) I apparently broke one of the wires soldered to one of the boards which caused a resistor to burn up, which has been replaced.
What I would like to to is power the monitor up without the HV power supply so I can check out the voltages on the LV supply to make sure everything there is working properly before I try to power up the HV supply. There was a post from back in 2011 regarding doing just this with a 12 ohm resistor but not which connections this was across. I really don't want to let the magic smoke out again.
Thanks,
Ed
- Board index Focused Discussion Test Equipment & RF Equipment Alignment
- Search
-
- It is currently Thu May 09, 2024 3:19 pm
- All times are UTC-08:00
R2001A HV Power Supply
This forum exists for the purposes for discussing service monitors (This includes but is not limited to Motorola, HP, Aeroflex, GD, etc). Additional topics allowed include test procedures, interpretation of test results, where to find information about specific tests, antenna VSWR, return loss testing, duplexer and filter alignment, etc.
Moderator: Queue Moderator
-
- New User
- Posts: 1
- Joined: Wed Feb 01, 2017 3:00 pm
- What radios do you own?: MTS2000, Spectra
Return to “Test Equipment & RF Equipment Alignment”
Jump to
- Administrative
- ↳ Announcements and Forum News
- ↳ Forum Rules
- General
- ↳ General Motorola Solutions & Legacy Radio Discussion
- ↳ Radio Programming
- ↳ Software & Firmware Releases & Issues
- ↳ Codeplug Information
- ↳ NFPA 1802 Discussion
- Current Motorola Solutions Public Safety / Astro Product Line
- ↳ APX NEXT
- ↳ APX Series Subscribers
- ↳ ASTRO Series (Astro Saber, Spectra, XTS3000/3500) Subscribers
- ↳ ASTRO25 Series (XTS/XTL 1500/2500/5000) Subscribers
- ↳ ASTRO Experimental - How to do things a little out of the box
- ↳ ASTRO Products Feature Requests & Future Speculation
- ↳ Legacy Batboard Motorola ASTRO (VSELP/IMBE/AMBE) Equipment Forum
- Current Motorola Solutions Professional / Business Product Lines
- ↳ MotoTRBO ION Devices
- ↳ Motorola CP/CM Series Subscribers
- ↳ MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- ↳ MotoTRBO Portables and Mobiles (3xxx/5xxx/7xxx/SL) 2.0 Series Subscribers
- ↳ MotoTRBO Repeaters, Trunking, and Site Infrastructure
- ↳ MotoTRBO 3rd Party Application Discussion & Support
- ↳ MotoTRBO/Business Products Feature Requests & Future Speculation
- ↳ Experimental - How to do things a little out of the box
- Motorola System Infrastructure (Consoles, Base Stations, Repeaters, Trunking, etc.)
- ↳ Smartnet/Smartzone/Project 25 (Phase I/II) Systems
- ↳ Base Stations, Repeaters, General Infrastructure
- ↳ Consoles
- ↳ Experimental - Mods, and how to do things a little out of the box
- ↳ Infrastructure Product Feature Requests & Future Speculation
- Focused Discussion
- ↳ Motorola Digital and Voice Paging
- ↳ Converting Motorola Equipment to 900MHz Amateur
- ↳ Test Equipment & RF Equipment Alignment
- ↳ Vehicle Radio Installs
- ↳ Experimental and Next Generation LMR
- ↳ Motorola Digital Radio Compatability
- Off-Topic Discussion
- ↳ Vehicle Warning Equipment Discussion
- ↳ Computer/Technical Assistance
- ↳ Knowledge Base