p/n for XTS5000 keyloader cable please

hamptonbeach · Post by **hamptonbeach** » Wed Feb 16, 2005 10:09 am

Subject line says it all

I'm looking for the part number for the keyloader cable that will work with the XTS5000

Thanks,
Tom

Karl NVW · Post by **Karl NVW** » Wed Feb 16, 2005 10:31 am

TDN9390

hamptonbeach · Post by **hamptonbeach** » Wed Feb 16, 2005 11:19 am

Hi,

TDN9390D comes back as

"CABLE KEYLOAD MTS2000"

Does the MTS and XTS use the same cable??

Tom
N1AML

RESCUE161 · Post by **RESCUE161** » Wed Feb 16, 2005 11:22 am

They do use the same cable.

hamptonbeach · Post by **hamptonbeach** » Wed Feb 16, 2005 11:27 am

Thanks! I REALLY hate talking on the phone - which was why I posted the question here , but I just called M and confirmed that was true.

RESCUE161 · Post by **RESCUE161** » Wed Feb 16, 2005 11:30 am

I didn't realize how cheap they were, so I made my own. Now that I FINALLY got an MOL account, I see they aren't that bad. Lot's of other things aren't as bad as I origianlly thought either.

CTAMontrose · Post by **CTAMontrose** » Tue Feb 22, 2005 3:29 pm

rescue, do you still have the diagram to make one? my searching skills are eluding me if its posted around here..

thanks!

RESCUE161 · Post by **RESCUE161** » Tue Feb 22, 2005 9:38 pm

I do, but I'm on the way to work right now. I'll set you up later today!

RESCUE161 · Post by **RESCUE161** » Wed Feb 23, 2005 2:30 am

I take NO credit for this map-out of the cable. It does work very well! I had a link to the website that hosted it, but have lost it somewhere. Correct me if I'm wrong, but I think this is another r0f original.

MTS / XTS KVL Cable TDN9390D

KVL Connector, Face view, Lip/Screw Top

LIP HERE

1 o o 6

2 o o 7

3 o o 8

4 o o 9
--------><THUMB SCREW HERE
5 o o 10

Radio Connector, Face View, Spring/Clip Top

SPRING CLIP HERE

----o 7
1 o
----o 8
2 o
----o 9
3 o
----o 10
4 o
----o 11
5 o
----o 12
6 o
----o 13

KVL 1 --- NOT CONNECTED
KVL 2 --> RADIO 4,5,6
KVL 3 --> RADIO 13
KVL 4 --> RADIO 10
KVL 5 --> RADIO 11
KVL 6 --- NOT CONNECTED
KVL 7 --> RADIO 4,5,6
KVL 8 --> RADIO 13
KVL 9 --> RADIO 10
KVL 10 --> RADIO 11

(Edit: to allow for adding dashes. Spacing doesn't stay after posting, so dashes had to be added to keep the propper spaces on the connectors. Sorry for the confusion).

CTAMontrose · Post by **CTAMontrose** » Wed Feb 23, 2005 6:33 am

outstanding man! i appreciate it

ArmsonOeg · Post by **ArmsonOeg** » Sun Oct 22, 2006 1:25 pm

For those seeking to roll thier own. I suggest following this Correct MX diagram, not the one above

http://www.batlabs.com/images/mx300mic.gif

hamptonbeach · Post by **hamptonbeach** » Sun Oct 22, 2006 1:55 pm

Umm .. isn't that a mic schematic?

The subject here is a keyloader cable

jnglmassiv · Post by **jnglmassiv** » Sun Oct 22, 2006 2:35 pm

hamptonbeach wrote:Umm .. isn't that a mic schematic?

The subject here is a keyloader cable

I think ArmsonOeg is saying that the linked drawing is easier to read.

borisf · Post by **borisf** » Tue Oct 31, 2006 7:16 am

Aren't we confusing Jedi and Saber a bit anyway?

mancow · Post by **mancow** » Mon Feb 12, 2007 6:59 pm

I just tried making this cable and I can't get it to work. I have a TKN8531B hirose cable that works with the saber hirose D adapers. I found a female hirose and installed that in a jedi connector where the audio jack normally goes. I figured I could wired up the right pins and have a jedi end for my XTS.

The diagram above shows the kvl pins basically bridged all the way across except the two top ones. I tried making the cable with the pins bridged and without but nothing works.

Does anyone have a real deal diagram of the wiring for a Jedi / XTS cable?