Have several Model 0105956V67 encryption boards that refuse to operate in XTS3K. Other model boards work find, just not these. Radio gives error code indicating it does not recognize board is installed. This particular board is the version that is supposed to do everything but DVP. Anyone seen anything similar?
Wyocommo
Encryption Issue in XTS3K
Moderator: Queue Moderator
yep
sure have
what is the host and dsp in your xts's?
what is the firmware rev on the boards?
doug
what is the host and dsp in your xts's?
what is the firmware rev on the boards?
doug
BRAVO MIKE JULIET ALPHA
"You can do whatever you want, there are just consequences..."
IF SOMEONE PM'S YOU - HAVE THE COURTESY TO REPLY.
"You can do whatever you want, there are just consequences..."
IF SOMEONE PM'S YOU - HAVE THE COURTESY TO REPLY.
XTS encryption
firm is 7.09.02
DSP is N08.02.04
Secure board is Rev A
DSP is N08.02.04
Secure board is Rev A
..
what is the secure board EMC Revision?
?
doug
?
doug
BRAVO MIKE JULIET ALPHA
"You can do whatever you want, there are just consequences..."
IF SOMEONE PM'S YOU - HAVE THE COURTESY TO REPLY.
"You can do whatever you want, there are just consequences..."
IF SOMEONE PM'S YOU - HAVE THE COURTESY TO REPLY.
XTS Encryption
Time to show my ignorance. Where is this info on the board or what format is it in? The paper label has 243-02 and GAM020FMBK.
"WORK sure gets in the way of PLAY"
...
install module
turn on secure hardware in the software
boot radio
put into self test mode
first HOST
then DSP
then
EMC VERSION
i am willing to bet you have some old secure hardware.... host 7/dsp 8 is very picky... you have to have at least EMC 2.xx (memory check here - i think) for the board to function....just checked my radio, my board is EMC 2.12 and works fine w/ host 7/dsp8
turn on secure hardware in the software
boot radio
put into self test mode
first HOST
then DSP
then
EMC VERSION
i am willing to bet you have some old secure hardware.... host 7/dsp 8 is very picky... you have to have at least EMC 2.xx (memory check here - i think) for the board to function....just checked my radio, my board is EMC 2.12 and works fine w/ host 7/dsp8
BRAVO MIKE JULIET ALPHA
"You can do whatever you want, there are just consequences..."
IF SOMEONE PM'S YOU - HAVE THE COURTESY TO REPLY.
"You can do whatever you want, there are just consequences..."
IF SOMEONE PM'S YOU - HAVE THE COURTESY TO REPLY.
XTS encryption
I have 3.56 EMC in this unit. I am beginning to think it is something peculiar to this secure board model, since other secure boards work fine in this radio.
I have tried 3 different boards in the three different radios with the same result.
I have tried 3 different boards in the three different radios with the same result.
"WORK sure gets in the way of PLAY"
xts again
I stand corrected. Read wrong radio. I cannot read the EMC version because the radio does not recognize that the board is installed. It gives an error 09-10 which indicates that the micro was unable to communicate with the module.
"WORK sure gets in the way of PLAY"
...
yes, i have DEFINATELY experienced what you are seeing.
the EMC in the board is too old for the host to recognize it.
to verify, the best way is to find a host 5/6 xts and try to boot it with the board installed
doug
the EMC in the board is too old for the host to recognize it.
to verify, the best way is to find a host 5/6 xts and try to boot it with the board installed
doug
BRAVO MIKE JULIET ALPHA
"You can do whatever you want, there are just consequences..."
IF SOMEONE PM'S YOU - HAVE THE COURTESY TO REPLY.
"You can do whatever you want, there are just consequences..."
IF SOMEONE PM'S YOU - HAVE THE COURTESY TO REPLY.
...
i had one here a few months ago... was the same part number... and had the same problem.
doug
doug
BRAVO MIKE JULIET ALPHA
"You can do whatever you want, there are just consequences..."
IF SOMEONE PM'S YOU - HAVE THE COURTESY TO REPLY.
"You can do whatever you want, there are just consequences..."
IF SOMEONE PM'S YOU - HAVE THE COURTESY TO REPLY.
Re: ...
Of course, there's also the potential that the crypto board is simply b0rked...batdude wrote:i had one here a few months ago... was the same part number... and had the same problem.
doug
XTS encryption
Could be that all three boards are bad. I will look for an older host and dsp and try them on that.
"WORK sure gets in the way of PLAY"
