Need P/N for Center Pin of XTS PS Mic

Fuel4300 · Post by **Fuel4300** » Wed Mar 15, 2006 3:57 pm

I have an XTS Public Safety Mic thats apparently missing the center pin on the mic side of the part that connects to the adapter. So I have two questions:

1. Is it possible to open the connector and replace this part?
2. If so, anyone have the part number so I can order one?

This thing came from ebay so who knows why the pin is missing. I havent tried taking the connector apart yet.

Thanks in advance,

Mike

spectragod · Post by **spectragod** » Wed Mar 15, 2006 4:54 pm

I have a couple of extra P.S. mics for XTS if you need one.

SG

Fuel4300 · Post by **Fuel4300** » Fri Mar 17, 2006 2:08 pm

Thanks for the offer. I would rather, for now, try to fix this one.

Does a manual exist for this thing?

Mike

Jason · Post by **Jason** » Sun Mar 19, 2006 3:44 pm

Motorola will sell you a replacement cable harness, likely more than you can buy a used replacement for.

Those small parts arent available individually, but rather as a kit.

Fuel4300 · Post by **Fuel4300** » Sun Mar 19, 2006 5:13 pm

Jason wrote:Motorola will sell you a replacement cable harness, likely more than you can buy a used replacement for.

Those small parts arent available individually, but rather as a kit.

Do you have a p/n for the kit? It is at least worth getting a price off of MOL.

Thanks,

Mike

Jason · Post by **Jason** » Mon Mar 20, 2006 11:06 am

Ill see if i can find one for you.

Jason · Post by **Jason** » Mon Mar 20, 2006 2:51 pm

Did some reasearch on this for you, it appears the cord assembly is not available, as it requires a factory test procedure before it ships. An MSS can probably get it, IMHO. In fact, the parts are however, at least they do have a part number, not sure on availability. Call AAD (well, what used to be) they should be able to get you a price.

The previous commentary about the small parts not being available was incorrect. The standard JEDI NMN6191/6193/6193SP03 mics are not repairable, but only can have the cordset, ptt lever, and clip replaced.

Here are a few screenshots I made for you, and the group. Should be handy to keep on hand.

As always all materials are copyright Motorola, Inc.

Fuel4300 · Post by **Fuel4300** » Mon Mar 20, 2006 5:38 pm

Great, thats exactly what I was looking for!

Thanks a lot!

Mike

rmiles · Post by **rmiles** » Fri Mar 24, 2006 8:13 am

I have one of these which I disassembled to repair. It was fairly easy to take apart, however, after I soldered the rf cable to part 47 show in the screen capture above, it still did not work. I too looked on MOL for a replacment cable to no avail. That mic is still sitting on my bench and still will not receive any RF from the antenna, other than that, it works fine.

abbylind · Post by **abbylind** » Fri Mar 24, 2006 8:20 am

Talk to Grem467 (Marc) he told me that some of the XTS RF adaptors are defective (center pin is broken internally) and they wont pass RF. I had one I was using on a XTS3K with XTSMVA no RF either.
For whats its worth

Fowler

rmiles · Post by **rmiles** » Fri Mar 24, 2006 8:29 am

Good thought, but I tried two different rf adaptors and the PSM still does not work.

motoapco25 · Post by **motoapco25** » Thu Mar 30, 2006 6:04 pm

is there a place to get cheap RF Adaptors for the XTS PS mic?

Need P/N for Center Pin of XTS PS Mic

Need P/N for Center Pin of XTS PS Mic

psm

Re: psm

PSM Parts list