HT SERIES CHARGER INFO

FDNY · Post by **FDNY** » Thu Mar 14, 2002 8:21 pm

hi guys,

i need a model number for a charger, that can charge up nickel metal hydride batteries for my HT1000 & JT1000 SERIES...ANYONE KNOW IF MOTOROLA MAKES ONE AND IF SO WHAT IS THE MODEL NUMBER

THANKS

Tom in D.C. · Post by **Tom in D.C.** » Fri Mar 15, 2002 9:16 am

I can't give you a model number but any NiCD charger will work fine with NiMH batteries.

Tom, W2NJS
...in D.C.

streaker · Post by **streaker** » Fri Mar 15, 2002 9:27 am

NTN1171A is the model charger I am using for my JT1000 with a nickel metal hydride battery. Yes that is a Motorola Part. I would imagine it is still available.

Eric

perthcom · Post by **perthcom** » Fri Mar 15, 2002 9:37 am

Hi

Not all chargers can charge Nickel

Metalhydride batteries. NiMH are finicky batteries and the charger must recognize the the signs that the battery is charged.

For the HT-1000 Motorola has a RPX4747 Bi-Chemistry Intellicharger II and the NTN1168 Rapid Enhanced charger. The NTN1177 gang charger can also be used.

The NTN1174 overnight charger and NTN1171 single rapid chargers should NOT be used with NiMH batteries. The NTN1171 has been replaced by the RPX4747 Bi-Chemstry charger.

I have both the RPX4747 and NTN1168 in stock, email me if you are interested.

cheers
Bruce

<font size=-1>[ This Message was edited by: perthcom on 2002-03-15 12:41 ]</font>

streaker · Post by **streaker** » Fri Mar 15, 2002 9:59 am

When I bought the JT1000 new that's what was shipped to me. A High Capacity Ni-MH with the NTN1171A. I get over a year of good use out of it. I even leave it on in the charger. I suppose there is always the potential for trouble though. Just figured I'd share my experience. I'd probably take perthcom's advice though, I am just going on what has worked well for me, not what the books say.

SD70MAC · Post by **SD70MAC** » Fri Mar 15, 2002 2:19 pm

I have the 1171 charger for my JT1000 and it worked fine ,but now will not rapid charge my NiMH anymore for some reason.I would suggest getting the intelli-charger.The old charger still charges the nicad's.

FDNY · Post by **FDNY** » Fri Mar 15, 2002 6:03 pm

THANKS TO ALL WHO RESPONDED...AS USUAL YOU ARE A GREAT BUNCH ON BATLABS!!!!!!!!!!!!!!

Will · Post by **Will** » Fri Mar 15, 2002 8:48 pm

The standard rate NTN1174A charger is OK per Motorola for both battery types. Only down side is that it is designed for a 1200ma battery at 16 hours, that is 110 ma charge current. On the high capacity batteries, it takes longer, about 19 to 24 hours. I made a slight change in mine to charge at 150 ma on the 1500 mahr batteries, HI CAP.

perthcom · Post by **perthcom** » Sat Mar 16, 2002 2:21 pm

Hi
I'm not trying to be a jerk or anything, I was just going by what my Motorola info tells me for each charger.

Here is a quote directly from the Motorola site description of the WPNN4013 NiMH battery: "NiMH, 2000 mAh, 7.5V Battery (Only compatible with NTN1168 (Q224) & NTN1177 - NOT compatible with NTN1171 and NTN1174)"

And here is what it says about the NTN1174: "110 Volt Single Unit Slow Compact Charger (16 hours) (includes a compact standalone charger stand and a combination line cord/transformer/adapter) Not compatible with Nickel Metal Hydride Batteries."

Here is a link to an excellent article about battery chemistrys and the reasons why slow chargers like the the NTN1174 is not recommended for charging NiMH batteries. http://www.buchmann.ca/toc.asp

While the battery would get a recharge from such a charger, as a dealer it would come back to haunt me and i'd soon be exchanging chargers and batteries out of my pocket!

Its like you can deduct anything you want from your income tax return.. till ya get caught!

cheers

Bruce

Will · Post by **Will** » Sat Mar 16, 2002 6:02 pm

Perthcom, looks like the big M is going to sell more batteries and chargers.
Our recomendations, as I stated here are from engineering evaluation and many tests. This is valid for the "slow" 1/10C chargers.

Will · Post by **Will** » Sat Mar 16, 2002 6:35 pm

In the Jedi SLOW charger, a "Fat" battery requires 16 to 20 hrs in the slow charger.
There is a minor feild modification for the single rate charger to increase the charge curent to 150 miliamps (from 110 ma) for use with the Fat battery, 1500 MAH.

MRFLASHPORT · Post by **MRFLASHPORT** » Sat Mar 16, 2002 8:23 pm

I use the NTN1171A to charge W+W NiMH batteries which are 2700 mAh.

The charger works fine. I've had no problems at all. The Batteries last a good three days.

I highly recommend these batteries to
anyone. They are simply the best!

Johnny Galaga · Post by **Johnny Galaga** » Thu Jul 01, 2004 11:49 am

perthcom wrote:Hi

Not all chargers can charge Nickel

Metalhydride batteries. NiMH are finicky batteries and the charger must recognize the the signs that the battery is charged.

For the HT-1000 Motorola has a RPX4747 Bi-Chemistry Intellicharger II and the NTN1168 Rapid Enhanced charger. The NTN1177 gang charger can also be used.

I Have an NTN1177A, but it has a sticker on each bay that says to only charge NiCD's in it.

craig · Post by **craig** » Tue Jan 09, 2007 10:53 am

Does anyone know off hand the specs of the wall wart that is used with the NTN1174 slow charger. I am looking to buy a replacement power supply for it without paying /\/\ prices and need to know the following: volts, milliamps, polarity, and any other information you guys think is important to know. I am looking for 110v specs. I have one of those radio shack interchangable power supplies around here and maybe I'll use that if it matches the Motorola spec. I just don't have a motorola power supply in front of me to get the information myself.

Thanks!

Will · Post by **Will** » Tue Jan 09, 2007 10:53 pm

12 to 16 volts DC at 200 ma should do it. Charger regulates the current to the battery depending on the battery capacity select pin, 120 to 150 MA.

Charger can be 'mod'ed' to provide up to 200 ma for hi capacity batteries.

craig · Post by **craig** » Wed Jan 10, 2007 4:52 am

I am presuming positive tip, is that correct?

W6JK · Post by **W6JK** » Wed Jan 10, 2007 8:10 am

Yes, positive tip, 1.1 mm size (size H at Radio Shack).

Jeff

craig · Post by **craig** » Wed Jan 10, 2007 2:32 pm

Thanks everyone for the great information.

Craig

W6JK · Post by **W6JK** » Wed Jan 10, 2007 5:14 pm

Oops! I shouldn.t have posted that from memory, apparently. The connector is 1.3 mm ID, 3.5 mm OD. Size H at the Shack was correct, though, and the catalog number is 274-1571. I've been to 5 stores now looking for them, and only two had any (note past tense). But you can order them from the web site.

Jeff

craig · Post by **craig** » Wed Jan 10, 2007 8:24 pm

Thanks again for the info!

W6JK · Post by **W6JK** » Sat Jan 13, 2007 8:58 pm

This seems like a good place for the following...

In the course of accumulating various GTX and Jedi radios to play with, I ended up with a lot of chargers without power supplies. It escapes me how people can think those are less important, it's not like the charger is any good without the supply, but somehow the supplies seem to be what goes astray. Maybe they're behind the dryer with the missing socks. Anyway, I made up the following chart to take along to swap meets and surplus stores in search of substitute parts. For each charger it describes first the supply, and then the connector needed for it. Maybe someone else will find it useful too.

Charger Power Supplies - All are center pin +

---------------------------------------------------------------

Standard charger (Jedi NTN1174A or GTX HTN9702A):

Model: 2580955Z02 12 VDC 2.4 W (200 mA)

1.3 mm ID, 3.5 mm OD. Size H at the Shack, catalog # 274-1571

---------------------------------------------------------------

GTX Rapid Charger HTN9042A:

Model: 2580600E01 13.8 VDC 0.9 A

2.5 mm ID, 5.5 mm OD. Size N at the Shack, catalog # 274-1573

---------------------------------------------------------------

Jedi Rapid Charger NTN1171A:

Model: 2580162R01 13.8 VDC 1.5 A

2.5 mm ID, 5.5 mm OD. Size N at the Shack, catalog # 274-1573

---------------------------------------------------------------

Jeff

HT SERIES CHARGER INFO

Power supply

Positive tip

Thanks!

Thanks again