XTS 2500 Volume

pluto1914 · Post by **pluto1914** » Fri Aug 24, 2007 4:53 am

Is there any way to boost the volume of the XTS2500 through the CPS or other means.

Bruce1807 · Post by **Bruce1807** » Fri Aug 24, 2007 7:53 am

audio out is on the accessory connector.
From there it is simple to add an amplifier or whatever.

The Pager Geek · Post by **The Pager Geek** » Fri Aug 24, 2007 9:28 am

Replace R505 10k resistor with a 2k.

Simple, but you need sharp SMT skills for soldering and unsoldering.

Works great, louder than an HT1000. Just did ~180 of them.
tpg

pluto1914 · Post by **pluto1914** » Fri Aug 24, 2007 2:25 pm

I'll have to have the radio shop do that...We had a drill today where 20 XTS2500's were used and the only complaint was that it was too quiet. Thanks!

pluto1914 · Post by **pluto1914** » Fri Aug 24, 2007 5:05 pm

was there ever a technical service bulletin regarding this?

The Pager Geek · Post by **The Pager Geek** » Fri Aug 24, 2007 5:53 pm

pluto1914 wrote:was there ever a technical service bulletin regarding this?

Not officially, but if you have your radio shop open a case with the product group at Motorola they'll get an "Oh.... uh... yeah. Do this..."

tpg

pluto1914 · Post by **pluto1914** » Fri Aug 24, 2007 7:16 pm

oh ok....so the Oh, Uh... Do This is probably not covered under the warranty...

The Pager Geek · Post by **The Pager Geek** » Fri Aug 24, 2007 8:42 pm

pluto1914 wrote:oh ok....so the Oh, Uh... Do This is probably not covered under the warranty...

Motorola inconsistency. 1 Dept, Motorola paid for it, the other they didn't.

There is also a shield to be added to the front housing depending how old the radios are. changes the acoustical properties of the radio.

Good luck

tpg

Bruce1807 · Post by **Bruce1807** » Sat Aug 25, 2007 7:11 am

Hope they are not IS radios as they wont br if you make a mod like that!

pluto1914 · Post by **pluto1914** » Sat Aug 25, 2007 9:13 am

well there is no label on them that says they are intrinsically safe...

The Pager Geek · Post by **The Pager Geek** » Sat Aug 25, 2007 9:37 am

If they ARE IS, I suggest shipping them back to M for the upgrade. However, they may not come back as XTS2500's...

tpg

pluto1914 · Post by **pluto1914** » Sat Aug 25, 2007 1:02 pm

what would they come back as, mutant XTS2500's?

The Pager Geek · Post by **The Pager Geek** » Sat Aug 25, 2007 1:42 pm

could be anything based on my recent dealings with them. Ship a XTS1500, get a CP200 back. I wasn't happy. Neither was the customer.

tpg

mr.syntrx · Post by **mr.syntrx** » Sat Aug 25, 2007 9:57 pm

Too bad you can't ship out a CP200 and get an XTS 5000R III with AES, FPP, trunking etc back.

The Pager Geek · Post by **The Pager Geek** » Sat Aug 25, 2007 10:48 pm

Funny, Motorola never gets angry calls about that....

tpg

pluto1914 · Post by **pluto1914** » Wed Sep 12, 2007 1:25 pm

The Pager Geek wrote:
pluto1914 wrote:was there ever a technical service bulletin regarding this?
Not officially, but if you have your radio shop open a case with the product group at Motorola they'll get an "Oh.... uh... yeah. Do this..."

tpg

Our radio shop looked into this issue with Motorola and couldn't get anywhere, can someone give me some more details on what they should be looking for? Such as TSB number contact person?

Thanks...

David

havmedic26 · Post by **havmedic26** » Thu Jan 22, 2009 1:12 pm

Can anyone tell me how to locate R505? I definitely have the skills to do the switch, but without a schematic or diagram....? I have been out of the electrical engineering field for 13 years now. When I went to college resistors looked very different. Any help would be great....

thanks

XTS 2500 Volume

XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume

Re: XTS 2500 Volume