Just recently purchased a JT1000 used.
It seems when using the DTMF keypad for the feature/digits to be recognized I must press down very hard.
Is this an easy fix? If I need to take to a shop what is the ballpark cost?
JT1000 DTMF Keys
Moderator: Queue Moderator
Re: JT1000 DTMF Keys
Sometimes the key pad gets dirty. You'll have to crack open the case and remove the keypad from the front cover, remover the rubber pad and clean the board. Ive used alcohol (sparingly) with good results.
Good luck
Fowler
KC5AEE
Good luck
Fowler
KC5AEE
Q: Does this unit come with a speaker?
A: hello yes its in the radio thanks
A: hello yes its in the radio thanks
-
motorola_otaku
- Posts: 1854
- Joined: Tue Jan 13, 2004 7:03 am
Re: JT1000 DTMF Keys
99% pure isopropyl alcohol on cotton swabs works a treat for keypad cleaning. You can also use it on the keypad membrane and around the button holes on the front housing to clean out "gunk" if the buttons are sticky.
Re: JT1000 DTMF Keys
Don't have a service manual, how do I crack open the case?
I'm assuming the obvious, take battery off, buttons/knobs off.
What's the next step
I'm assuming the obvious, take battery off, buttons/knobs off.
What's the next step
-
Terry_Glover
- Posts: 439
- Joined: Mon Feb 20, 2006 5:42 pm
Re: JT1000 DTMF Keys
Yeah, remove the battery, antenna and channel and volume knobs then.....
Small flat blade screwdriver is all that's needed to seperate case from chassis, as shown.
You don't need any special Motorola tool to lift the connector lockdown tab. Just use your fingernail.
Terry
Small flat blade screwdriver is all that's needed to seperate case from chassis, as shown.
You don't need any special Motorola tool to lift the connector lockdown tab. Just use your fingernail.
Terry
Terry
Re: JT1000 DTMF Keys
Thanks Terry, got the cover off.
Do you have the diagram for removing the keypad from the housing?
Appreciate it
Do you have the diagram for removing the keypad from the housing?
Appreciate it
-
Terry_Glover
- Posts: 439
- Joined: Mon Feb 20, 2006 5:42 pm
Re: JT1000 DTMF Keys
JT1000 is a front display so you can disregard step 1.
It's been a couple of years since I replaced a keypad housing, but IIRC you may not need to remove the speaker and mic to lift the keypad board. Skip to step 6 (highlighted in yellow) if speaker and flex components will NOT interfere with removing the keypad board..
Remove the display board as shown in step 6 below and the keypad rubber just lifts out from underneath the board.
Especially important if radios are used by paramedics or first-aide personell:>>>
I always took the knobs, orange emergency button rubber, rubber keypad and the completely stripped down front housing and gently washed them in warm water with dish wash detergent (Ivory, Dawn, Ajax for dishes, etc.) and an old, soft toothbrush to clean units that had softdrink, coffee, blood, body fluids, snot or puke on them. Rinse thourghly and allow to completely air dry before reassembly. They're now sanitary and no longer sticky!
This is what the single piece rubber keypad and display seal looks like.
Terry
It's been a couple of years since I replaced a keypad housing, but IIRC you may not need to remove the speaker and mic to lift the keypad board. Skip to step 6 (highlighted in yellow) if speaker and flex components will NOT interfere with removing the keypad board..
Remove the display board as shown in step 6 below and the keypad rubber just lifts out from underneath the board.
Especially important if radios are used by paramedics or first-aide personell:>>>
I always took the knobs, orange emergency button rubber, rubber keypad and the completely stripped down front housing and gently washed them in warm water with dish wash detergent (Ivory, Dawn, Ajax for dishes, etc.) and an old, soft toothbrush to clean units that had softdrink, coffee, blood, body fluids, snot or puke on them. Rinse thourghly and allow to completely air dry before reassembly. They're now sanitary and no longer sticky!
This is what the single piece rubber keypad and display seal looks like.
Terry
Terry
Re: JT1000 DTMF Keys
Terry is right on and a good instructor!
You"ll be servicing Jedi series radios like a pro before you know it!
I clean the rubber pads as Terry advised also.
I use a citrus based cleaner to scrub the plastic housing with an old toothbrush. Makes it look new and a smells better to boot!
Fowler
KC5AEE
You"ll be servicing Jedi series radios like a pro before you know it!
I clean the rubber pads as Terry advised also.
I use a citrus based cleaner to scrub the plastic housing with an old toothbrush. Makes it look new and a smells better to boot!
Fowler
KC5AEE
Q: Does this unit come with a speaker?
A: hello yes its in the radio thanks
A: hello yes its in the radio thanks
-
Terry_Glover
- Posts: 439
- Joined: Mon Feb 20, 2006 5:42 pm
Re: JT1000 DTMF Keys
Thanks Fowler! I've got several hundred refurbs under my belt by now.
I'm gonna try the citrus cleaner next time. The dishwash detergent leaves the housing really clean but looking dull. It never occured to me to try the citrus stuff. It's a natural disinfectant/sanitizer and the floors shine after the old lady mops with it... Agent Orange..., or whatever that stuff Billy Meyers (or is his name Billy Mayes???) sells on TV.
Thanks for that tip!
I'm gonna try the citrus cleaner next time. The dishwash detergent leaves the housing really clean but looking dull. It never occured to me to try the citrus stuff. It's a natural disinfectant/sanitizer and the floors shine after the old lady mops with it... Agent Orange..., or whatever that stuff Billy Meyers (or is his name Billy Mayes???) sells on TV.
Thanks for that tip!Terry
Re: JT1000 DTMF Keys
You bet Terry. Keep Billy Mays in business!
Fowler
Fowler
Q: Does this unit come with a speaker?
A: hello yes its in the radio thanks
A: hello yes its in the radio thanks