Page 1 of 1
Posted: Wed Jan 16, 2002 12:01 am
by Keygun
Hi.
Does any body know the (exact) difference between an NUE7231C rf-board (MTS2000) and
NUE7230C (GP1200)? I thought all MT/MTS/GP1200 boards within the same bandsplit/power are exactly the same. I replaced the defective MTS-board with the one taken out of an GP1200 and after retuning it works perfect (full specs). My JEDI-service-manual knows only the NUE7231C board. Has anyboady some infos about NUE7230C?? Maybe two different modelnumbers for the same thing???
Regards
Keygun
Posted: Wed Jan 16, 2002 12:53 am
by Will
Yes most Jedi RF boards are the same, just different numbers.
Look in the front pages of last years Price book and under exchange boards for a listing showing part numbers.
Glad that your swap worked out, good to know, got a few bad ones here too.
Posted: Wed Jan 16, 2002 1:05 am
by radioEd
On 2002-01-16 03:01, Keygun wrote:
Hi.
Does any body know the (exact) difference between an NUE7231C rf-board (MTS2000) and
NUE7230C (GP1200)? I thought all MT/MTS/GP1200 boards within the same bandsplit/power are exactly the same. I replaced the defective MTS-board with the one taken out of an GP1200 and after retuning it works perfect (full specs). My JEDI-service-manual knows only the NUE7231C board. Has anyboady some infos about NUE7230C?? Maybe two different modelnumbers for the same thing???
Regards
Keygun
I don't have a Price Book, thats another dept! but if you find NUE7230C let me know too! Cause I can't find it. All the others yes! Ed
Posted: Wed Jan 16, 2002 1:13 am
by Will
I find the NUE7231C for the R1, 403 to 470 and NUE7232C for R2 450 to 512 used on HT1000, JT1000 , MT2000, and MTS2000
Posted: Wed Jan 16, 2002 1:17 am
by radioEd
On 2002-01-16 04:13, Will wrote:
I find the NUE7231C for the R1, 403 to 470 and NUE7232C for R2 450 to 512 used on HT1000, JT1000 , MT2000, and MTS2000
Nothing on the NUE7230C ?? thanks for the reply Ed
Posted: Wed Jan 16, 2002 7:42 am
by wavetar
You know Motorola, one different component can make the entire board a different number. I've swapped many an RF board between MTX8000/HT1000/Visar radios. All worked just fine after tuning (and changing the RF connector on the Visar boards).
Todd
Posted: Wed Jan 16, 2002 8:22 am
by radioEd
Good ol Motorola, just like a "minefield"!
Posted: Thu Jan 17, 2002 11:12 am
by Keygun
On 2002-01-16 10:42, wavetar wrote:
You know Motorola, one different component can make the entire board a different number. I've swapped many an RF board between MTX8000/HT1000/Visar radios. All worked just fine after tuning (and changing the RF connector on the Visar boards).
Todd
The new board is working perfect and i have encountered no problems, even the radio is in heavy use.
Only with the old tuning-values the TX-power level was very much higher (7.2W instead of 3W!!!) after replacing (prior realignment). RX needed only a slight retuning.
Keygun
Posted: Thu Jan 17, 2002 4:51 pm
by Chris
Just for everyone's info, or maybe you guys know this already.
In each range of the Jedi RF board, there is a 2ppm and a 5ppm board, and each have their own separate part number.
Chris