Page 1 of 1
Posted: Fri Mar 15, 2002 9:47 pm
by watertooth
Hi, I am the proud owner of a VHF HT1000 model # H01KCC9AN3AC. No version of American rss supports it. Does anyone know what the radio is and what version rss would be required or if there is a way to use American rss.
Thanks, Elliot
<font size=-1>[ This Message was edited by: watertooth on 2002-03-16 19:43 ]</font>
Posted: Sat Mar 16, 2002 6:40 pm
by Will
If that model number IS correct, the "N" says it is a Tone Signaling radio.
Can you just "Read" the radio?
Posted: Sat Mar 16, 2002 8:07 pm
by watertooth
I have tried lab and 4 other American versions of rss and each says "block error" and tells me I'm using the wrong programmer so I have not read it but it works fine on the one channel thats in there so it seems like a good radio. Thanks for responding.
Elliot
Posted: Sat Mar 16, 2002 8:50 pm
by PCSAR 4x4 652
WHat programmer are you using. If it is not an actual RLN4008b Mot RIB, you may get errors. Check your BATTERY It's not the RSS having a problem, it is your rib if you get "wrong Programmer" instead of "codeplug too new/old".What versions of RSS and LAB are you using?
_________________
T. Freeman
PCSAR 4x4 Unit 652
PCSAR TAC Unit 705
<font size=-1>[ This Message was edited by: PCSAR 4x4 652 on 2002-03-16 23:57 ]</font>
Posted: Sat Mar 16, 2002 9:10 pm
by watertooth
Thanks, I am really happy that there are people who take the time to help. I have other VHF and UHF HT1000s as well as MTX9000s, MT & MTS2000s and a GP1200 that all work fine with my aftermarket rib & cabel and I was able to save an srecord of this mystery radio with mtsx lab as well. This makes me think that there is alternate software for this radio, kinda like the GP300-5tone.
Posted: Sun Mar 17, 2002 10:05 am
by wavetar
There's the possibility someone has dropped an MT2000 logic board into it, try reading it with the latest MTSX software, just for the hell of it.
Todd
Posted: Sun Mar 17, 2002 4:13 pm
by watertooth
I tried to read this mystery radio on the mtsx r06.00.00 rss. The progress bar went from 0 to 65 just fine but the error message said "codeplug too new". On the ht1000 rss versions the error message says "programmer not compatable". I looked up the model # and I think the last digit "C" stands for cenelic, whatever that means. I think it is some kind of Euro trunking. Even so, the radio works fine on the 151 MHz channel thats in there. HELP,
Elliot
Posted: Sun Mar 17, 2002 4:26 pm
by xmo
MTSX DOS based RSS latest version is R06.05.00 so 'codeplug too new' could be accurate when reading with R06.00.00.
You could also try MTSX CPS.
Posted: Sun Mar 17, 2002 5:33 pm
by Nand
Posted: Sun Mar 17, 2002 5:50 pm
by RadioSouth
Cenelec isn't a trunking protocol. It is a European organization similar to Factory Mutual(FM)in the US which tests/sets standards for items used in potentially hazardous atmospheres (intrinsic safe and the like).
Posted: Sun Mar 17, 2002 6:31 pm
by watertooth
Thank you all for the info and suggestions. I'm back from the drawing board to report that my mystery radio in the HT1000 case is really a GP900. Thanks for the link. It's not a great radio for the American market. Looks like no DPL, MDC or QCII. I will see what I can get out of it. Thanks again,
Elliot
<font size=-1>[ This Message was edited by: watertooth on 2002-03-17 22:06 ]</font>