Page 1 of 1
Does HT-1000 have a (Talk Around Mode)
Posted: Mon Jan 22, 2007 3:49 pm
by dbfd588
Does a HT-1000 have a button for Talk Around. Just say you have a duplex repeater system on channel 2. Is there a button to by-pass the repeator so that you can talk on the receive freq?
Posted: Mon Jan 22, 2007 3:51 pm
by NSPD
Yes, if it is programmed to have one.
Posted: Mon Jan 22, 2007 3:52 pm
by dbfd588
OK. Thanks.
Posted: Mon Jan 22, 2007 3:53 pm
by Grog
Would you program the ABC toggle for that?
Posted: Mon Jan 22, 2007 3:59 pm
by dbfd588
Im not sure. I think it would be one of the side buttons. The ABC positions are for scan operation I do believe. But Im really not sure. Thanks for bringing that issue up.
Posted: Mon Jan 22, 2007 4:07 pm
by Mfire39
You can assign a talkaround position to the A-B-C switch with no problem.
-Marc
Posted: Mon Jan 22, 2007 4:12 pm
by dbfd588
Can either of the side buttons be programmed for Talk Around. What are all the options for the ABC positions and all the options for the side buttons
Posted: Mon Jan 22, 2007 5:11 pm
by Mfire39
Here are the options for the A-B-C toggle and side buttons in a nutshell. They will vary slightly depending on the revision of HT1000 that you have ie, AN BN CN DN. These were taken from a DN codeplug....
The options for the A-B-C switch are used in pairs (Most of them) for each position, and some options are only able to be used with certain other options, unless you have a "certain version" of the software that will let you assign pretty much what you want to each position. This should give you the basic idea though of what you can assign.
-------------------------------------------------------------------------------------
The A-B-C switch options are as follows:
Scan prog on
Scan prog off
Scan on
Scan off
Direct
Repeat
Chan option squelch
Carrier Squelch
Tx Low Power
CSQ Tx
High Power
Low Power
Chan option Power
Tx PL Low power
Chan option Talkaround
Blank
------------------------------------------------------------------------------------
The options for the 3 side buttons are as follows, and this was taken from a DN revision codeplug:
RAT
Select
Single tone Encode 1
Single tone Encode 2
Scan Program Status
Blank
Monitor
Monitor/Scan program status
Light
Scan On/Off
-------------------------------------------------------------------------------------
Hope this helps a little...
-Marc
Posted: Mon Jan 22, 2007 5:16 pm
by dbfd588
Oh Thats helps alot. I really appreciate all the info and help
Posted: Mon Jan 22, 2007 6:24 pm
by RKG
Around here, the prevailing practice for HT1000 portable is:
A = Direct
B = Repeat (no scan)
C = Repeat w/scan.
Posted: Mon Jan 22, 2007 6:40 pm
by Will
Around here, the prevailing practice for HT1000 portable is:
A = Repeat w/PL on
B = Repeat w/Mon (no RX PL)
C = Direct TalkAround
Scan on top side button
Posted: Mon Jan 22, 2007 9:41 pm
by mt1000ff
Not a lot of repeaters around here. Simplex VHF
A= Scan program
B= Scan Off
C= Scan On
Posted: Tue Jan 23, 2007 2:25 am
by PhillyPhoto
I've run into not being able to do talk-around using any type of signaling, such as MDC etc...
Posted: Tue Jan 23, 2007 7:27 pm
by dbfd588
OK. Im wanting to be able to talk on repeators, also talk direct(TalkAround), also be able to scan and be able to select the channels to be scanned. Is it possible for the local radio shop to do this. Which buttons should be be assighned to which function. I new to the ht-1000 radios. Just trying to figure out how to have it programmed.
Posted: Tue Jan 23, 2007 10:39 pm
by Will
dbfd588 wrote:
Is it possible for the local radio shop to do this. .
I do not know if the "shop" can "do this". But I ( and a couple of others here) can program them the way you need.