Page 1 of 1
HMN4079D Programming Issue
Posted: Sun Dec 21, 2008 3:51 pm
by rc50won
HNM4079D on XTL5000 O5 Control Head
Model M20QSS9PW1AN
Flash: 580208-001C80-9
Firmware 12
CPS 12
When I try to program the three side buttons, the radio ignores what I program:
Upper/No-dot program as Scan gives me Unpr
Middle/1-dot program as ZnDn gives me Unpr
Bottom/2-dot program as ZnUp gives me Unpr
No matter what combinations I try, it does not take. Sometimes the Upper and Middle keys program but not correctly. The bottom 2-dot key never programs. I have tried programming the Trunk Side the same as the Conventional Side and also leaving the Trunk Side unprogrammed. The radio is used for Conventional only.
Do I have to tell the radio that there is an HNM4079 attached? How?
Okay, I'm confused.
Marshall
Re: HMN4079D Programming Issue
Posted: Sun Dec 21, 2008 3:55 pm
by escomm
Do you have those functions as menu items?
Re: HMN4079D Programming Issue
Posted: Sun Dec 21, 2008 4:30 pm
by rc50won
Yes I have SCAN and ZONE set as menu items.
Marshall
Re: HMN4079D Programming Issue
Posted: Sun Dec 21, 2008 5:49 pm
by Mfire39
Do you mean you have an 03 head and not an 05? There are no side buttons on an 05 head...
-Marc
Re: HMN4079D Programming Issue
Posted: Sun Dec 21, 2008 6:16 pm
by rc50won
Mfire39 wrote:Do you mean you have an 03 head and not an 05? There are no side buttons on an 05 head...
But there are on the hmn4079 mic. /\/\
-Marc
Re: HMN4079D Programming Issue
Posted: Sun Dec 21, 2008 6:30 pm
by escomm
rc50won wrote:Yes I have SCAN and ZONE set as menu items.
Marshall
I suspect if you take them out as menu items for the soft keys on the head that they will start working on the DTMF mic.
Re: HMN4079D Programming Issue
Posted: Sun Dec 21, 2008 7:02 pm
by rc50won
I changed the codeplug and will download it in the morning. Thanks for the help.
Marshall
escomm wrote:rc50won wrote:Yes I have SCAN and ZONE set as menu items.
Marshall
I suspect if you take them out as menu items for the soft keys on the head that they will start working on the DTMF mic.
Re: HMN4079D Programming Issue
Posted: Sun Dec 21, 2008 7:38 pm
by Mfire39
rc50won wrote:Mfire39 wrote:Do you mean you have an 03 head and not an 05? There are no side buttons on an 05 head...
But there are on the hmn4079 mic. /\/\
-Marc
You're right, I was having a little mental moment over here..
-Marc
Re: HMN4079D Programming Issue
Posted: Mon Dec 22, 2008 4:46 am
by rc50won
Taking the duplicate commands out of the O5 head menu did not work.
I am seeing a pattern though. Whatever I program into the Upper/No-Dot button winds up being programmed into the O5 Head Red button. Items programmed into the 1 and 2 Dot buttons move up to the No-Dot and 1-Dot buttons and the 2-Dot button is blank. I can repeat this pattern with different commands.
At this point I am guessing that either I have a bad codeplug or I just discovered a firmware issue.
Marshall
Re: HMN4079D Programming Issue
Posted: Wed Feb 23, 2011 7:29 am
by MotoFAN
Guys,
Few questions about HMN4079D:
1. Any way to reprogram some of 4 top front buttons?
2. How to choose menu items from this mic? I am able to navigate through menu by navipad on mic, but I have no ideas how to select/press exact item.
P.S.
3 side buttons already programmed, but it's not enough for me.