Batboard

JohnDo

That would be great, love to hear how you get on.

Merry Christmas to all

JohnDo

I found the info I had created

use at your own risk

Service Monitor to KVL

15 pin D....................Key loader P4

14--------------------------1 GND
12--------------------------2 KEY
13--------------------------3 KID
15--------------------------4 WE
N/C------------------------5

From ...

JohnDo

Great

I did try to figure out the pinouts, I recall making an excel sheet at the time however I cannot find it. I shall look harder for it.

I do recall it was not a straight through cable based on my research at the time.

JohnDo

I have repaired a XTL2500 with this same issue

You have to inject a tone into the mic port and trace the audio path with a scope to identify the faulty component, In my case it was a faulty mux

DSM describes a procedure for this

JohnDo

I have been down this road in the past, I found nothing.

After researching the R2000 service manual I was able to make a cable to connect the service monitor to the KVL and to a portable for keyloading.

I was able to load a test key into a portable from the monitor however I could not load the ...

JohnDo

The R2200 Service manual is a good read as well, describes the functionality of the features of the service monitor and at the end of the manual it has information on how to connect equipment to the service monitor.

JohnDo

Hi Guys

I need to build a cable to go from the R2014D service monitor to the RTL4200A secure junction box. Does anyone know the pinouts from the D15 connector on the service monitor to the junction box. I have a feeling its not 1-1 through to 15-15.

RTL4200A to KVL cable schematic would be helpful ...

JohnDo

Your should try and read the radio with the Tuner CPS and if successful record your tuning values.

jamming another S-Record in there will overwrite the tuning values and the serial number of your XTS

You may not be able to just write you existing code plug to the Radio if the S-Record's model and ...

JohnDo

R.2024D/HS With high stability oscillator, IEEE-488 Bus, SECURENET options DES, DES-XL, DVP, DVP-XL

JohnDo

I have taken some more measurements on the A9A4 board.

I think the Offset Loop is working and my problem is the Translation Loop. Below are my findings

Offset Loop
Q2 Base = a steady 24.003MHz clean sine wave 9.1vp-p
Q2 Collector = a steady 24.003MHz clean sine wave 10.1vp-p
R45 = a steady 24 ...

JohnDo

try resetting the setting to default for all parameters. this will also loose stored frequencies

JohnDo

Thanks for the reply DJP126

I had taken some measurments from the A9A4 Board a while ago. My notes show

- the output of A9A4 at R79, I get 59.45MHz 200mV P-P where the schematic states 60.5MHz 1.8v p-p
- the shematic notes at the junction of R37 & CR11 f24= 24.003MHz 7VDC, here I have nothing but ...

JohnDo

Hi Guys

I have a R2001D that will not lock on to a frequency for RX or TX. The monitor has a good 10Mhz reff signal so I know its not the switch position. I have also attempted prividing a known good 10Mhz reff to the unit to no avail.

I have performed some tests from the service manual and have ...

JohnDo

Could be the A4 Control Board,

Do you have the Service Manual for the R2001D ?

JohnDo

Hi Nrembis

I was in the same boat as you and wanted a Service Monitor for simular resons. As mentioned in this tread you will start to learn alot more about things and will start to want more featurs out of your Service Monitor. I got myself a R2024D/HS and have been very happy with it. I did alot ...

JohnDo

Its Good to see the forum back up again, I was bitten by the Moto bug back in 1991 when I did work experience in a MSS. I then stared my collection of Moto gear and stared tinkering as a hobbyist. This place has been invaluable with helping me repair and understand Moto Radios and it would be a ...

JohnDo

FL 01/92 referrs to an error in the internal part of the codeplug (as opposed to the external part of the codeplug, which would be FL 01/82). CPS will seldom fix a codeplug with this error.

Exactly, that internal part of the codeplug contains the tuning partition. One thing you may try is read ...

JohnDo

problem solved. I sourced a NTN5832B and it works Great

thanks

JohnDo

so am I correct to assume the the below modules would work in a system saber on conventional chanels for use with DVP with a T3010BX KVL

o NTN5832 Smartnet DVP
o NTN5760 OTAR DVP
o NTN7288 Multikey DVP (replaced with NTN5755)

regards
John

JohnDo

I was very surprised when I couldnt toolproof it.

JohnDo

thanks

I missed the link

JohnDo

do system saber's require different modules to sabers ?

JohnDo

Rumor says that European MTS2000 (The one with "MADE IN EC" in the back) are not toolproof-able, even though they are in R06.XX. I haven't tried this myself but that might explain what you are seeing

This is true....

Jim

Is this verified? The EU models are actually NOT tool proof?

It does ...

JohnDo

Hi

I have a couple of System Saber3's that I would like to get working with DVP. When I install the NTN4711B DVP modules in them the radio will not power up, no display and no TX or RX.

the System Sabers are CON-6

I know the DVP modules are OK as when I install them into Saber's I can load a ...

JohnDo

Sounds like the Radio has been Inhibited. UHF can be inhibited as well, You get the self test screen and then the screen goes blank then thats its. no error on the display.

you can no longer acceess the diagnostics section by pessing the key above the PTT 5 times either

you could try reading the ...

JohnDo

May you rest in peace Monty

My condolences to the Monty's family and freinds.

John

JohnDo

you can disable the monitor button in the rss. take a look at your radio options

JohnDo

Im pretty sure VICPOL started using sabers in 86

JK

JohnDo

Hi,

Have you tried changing channels on your WLAN, do you have the option to change channels on your WLAN. I had an issue where my roller door kept randomly opening, once I figured it was the WLAN i changed it operating channel and all was well. Are you %100 sure its the WLAN, did you turn it off ...

JohnDo

I hear you can put a MTS2000 in (open mode) system watch mode
http://batlabs.enterzone.net/mtsx.html

anyone done this in Australia yet on the GRN if so could yall help...

John

JohnDo

they also bounce, and come back for more.

JohnDo

Yes its the same for saber III

JK

JohnDo

Hi Daniel,

I live in South Australia and they have moved to the new radio system here as well, Over here there on the UHF low band as you stated and its Trunked and they are running Digital Encryption, DES I think,

I dont see the police department leaking out the DES key in a hurry so to be ...

JohnDo

Here in Australia We also Use FIGJAM

anyone of you yanks know that one

(You probably do just adding my acronym)

JohnDo

Hi

As Far as I know the saber 1 to 3 do not support Selective Calling

the Mx 1000 2000 3000 ( Eurapean saber ) series radios do have Selective call and you should be able to disable MDC from every TX

Hope this helps

Marry Christmas to All

John

JohnDo

If the radio had originally belonged to a system and was lost or whatever it may have been killed from the console. If this happened the radio needs to go to a MSS to reprogrammed.
Aaron

Pls Ignore my ignorance but can this be done with saber ( not astro ) series radio ????

Regards
John

JohnDo

Hi Thanks For your input, Iv tried replacing the ref ocillator to no avail, when I get some time I will try the VCO.

Thank very much

JK

JohnDo

No only pre programmed frequencies as in channels.
You need the Rss for this type of radio, regular saber rss will NOT program this radio,

my question is this radio scan capable.

Regards John K

JohnDo

Hi All

I have a ht 600 that just beeps when its turned on continusly

it will read and wright

it has a good code plug in it and my programming equipment is ok

what does the constant beeping mean
( other that its broken )
regards
John K

JohnDo

Hello,

Iv got a saber UHF 440-470 split with a microphonic VCO

other than replacing the modual or the plastic bag trick is there any way to fix these moduals.

regards
John K

JohnDo

:-? Hi Guys

Here is some mo info on Mr Klez, Thanks to the CA web site,

I have cleaned klez of several pc only to be called in the next day coz they got it again. Make sure you delete it from your inbox so you dont run it again. also delete your deleted items.

anyway hers some more info on klez ...

JohnDo

Thanks William , N9LLO

Your on the ball William, Only difference is I had to enable option H401 for
clear voice slaved to a mode ( things must be different here in Australia ).

Thank you for help guys

Many Regards

John
Australia

JohnDo

Hi

I have programmed my saber clear as a saber secure ( to get the beep b4 tx ). The radio will rx and scan no probs but will not tx, it beeps as if the switch was in the wrong pos like on a secure saber with no encription modual installed.

No graet problem if it cant be solved, I will just make ...

JohnDo

Yeah I was

Thanks for that, but I ended up finding a compleat saber1 for around $80.00us Bargin

John

JohnDo

:-? You Guys have been stiffed Bad, Idd be leaving neg feedback for this Person But then remember that they may do the same to you if they havnt left feed back for you.

If you paid for the item and they recive payment then they should leave feedback then, ( I get my feedbacks b4 the items ) Sounds ...

JohnDo

Idd Like to thank Monty For taking the time and efort to help me fix my radio, In my view Monty has gone to Great trouble to supply me with step by step instructions and Picturs to help me out. It people like Monty that make this Forum Great.

thank You Monty and batlabs

Regards

John K

JohnDo

Just Hapend to be watching James Bond Movie ( live and let die ) while reading these posts,

Its cool You can still recive while the PTT is depressed. you even have vox when your too lazey to pick up the mic and push the PTT in a patrol car with an old syntor or the like.

Was there ever a movie ...

JohnDo

Here in Australia our police dept used saber III's , some bike patrols used MT 500, all Patrol cars used Philips FM91 radios,

Now they are going XTS, I guess you gatta keep with times !

JOhn

JohnDo

Hi Monty

I also have the same problem as described above

can you PLEASE help me as well.

I understand you dont want to be responcible for any further damage to my radio but things dont get any worse for me at this moment.

I will not hold you or anyone else responcible for further damage to my ...

JohnDo

Thanks for that input Will

Big M must let this company manufacture these units. I would of thought they would of put a patant on there parts, I guess if ther had M permision and built them to a specific quality. God knows. Ill Give them a go in my radios and let you know how I get on later. Thanks ...

Search found 68 matches

Re: R-2004D DES Cable for RTL-4200A

Re: R-2004D DES Cable for RTL-4200A

Re: R-2004D DES Cable for RTL-4200A

Re: PM1500 no modulation or PL encode

Re: R-2004D DES Cable for RTL-4200A

Re: books / resources to learn about servicing radio gear?

RTL4200A to R2014D cable

Re: motorola xts3000

Re: R-2001D Options/numbers

Re: R2001D not locking onto frequency

Re: Setting Peak Deviation Alarm on R-2001D

Re: R2001D not locking onto frequency

R2001D not locking onto frequency

Re: R2001D

Re: Service monitor for ht1000/mt2000

Re: Announcement... please read.

Re: How bad did I brick it?

Re: System Saber III and DVP

Re: System Saber III and DVP

Re: MTS2000 + TOOLPROOFING is MISSING?

Re: System Saber III and DVP

Re: System Saber III and DVP

Re: MTS2000 + TOOLPROOFING is MISSING?

System Saber III and DVP

Re: MTS2000 Programming Question

Ht 600 problem

Microphonic SABER UHF VCO

Saber Clear

Thank You Monty