Batboard

SD70MAC

I connected it to the radio with it on an closed it up in the stop all night and now it's charged. It was beeping, beeping and more beeping, so I just left it at the shop.

SD70MAC

Do you charge the battery in the HMN 4084 GPS mic with the XTS5000 on or off ? This one was a NOS never used.

SD70MAC

I have had my USED XPR7550 for over a year now and all the accessories will connect and disconnect at random(giving the tone over the radio). The accessory screw is tight and the housing is not damaged around the screw area. The decal ,tape(I can't remember the proper name) has a slight dimple at ...

SD70MAC

I printed out the data from both radios just in case I try it.

SD70MAC

If the error is based on features, firmware or otherwise. The older firmware radio has Connect Plus and the newer version doesn't. I don't use Connect Plus anyway.

Thanks for the reply !

73's

SD70MAC

I was trying to clone a XPR7550 that I have and I got a message, I did not continue.

"Codeplug versions in archives and device do not match. Fields in device that are not present or are out the vaild range in archive will be set to default values. Do you want to continue ? ".

Is this going to ...

SD70MAC

Hi Beekeper. I was just reading some posts here and saw this one. I have a CDM1250 42-50 Mhz split
that I would like to put on 6 Meter ham. How did you program it up into the 50-54 range.
Must be a "variant" version of CPS ? Interested in more info if you can share it on how this works.
Dick ...

SD70MAC

That would have been good to know when I had my HT1550XLS,I always hated those low capacity FPP batteries. I hope someone shares it some day !

SD70MAC

tvsjr wrote:To be clear, the board isn't the restriction. You have the channel set to Securenet encryption (DES/DES-XL) and Select or Secure strapping, which requires 5KHz deviation. Set the channel to clear and it'll work fine.

Thanks for the help

SD70MAC

That's what it was looking like to me too, but I wanted to check. Thanks for the reply.

SD70MAC

Do certain secure boards in an XTS5000 restrict you from narrow band ? I think the radio has DES XL ?

SD70MAC

I done the CDM1250 42-50 I have with the same CPS mod and it works fine so far.

SD70MAC

I would say it is a flex issue,or the radio was taken apart and the flex was not reseated correctly.

SD70MAC

another way to view pictures

http://forums.radioreference.com/motoro ... ost1847308

SD70MAC

I was fixing another W3 and it did not have as hot of a mic as the one I have so I had to make a revision to my mod.

Cut out the mic holder that it fits in from the factory.

http://s1240.beta.photobucket.com/user/railroadradionc/media/2012-10-31_19-46-51_421.jpg.html?sort=3&o=5#/user ...

SD70MAC

I don't have any insight on how to get this to work,but I have some questions about the Euro HHCH. What does the inside of it look like ? How did Motorola shield the Mic to stop the cross talk problem that the W3 Spectra's have ? Or did they fix it ? I have stopped the problem in my W3 ,but I did ...

SD70MAC

Here is the Mouser Part # for sheet of the shield material. It is 0.1mm thick and about 8" x 11" before you cut it to fit.

Mouser P/N 517-AB5010S

http://forums.radioreference.com/motoro ... ost1813307

SD70MAC

I been racking my brain to fix my W3's transmit hum and I finally found a way to fix it and here it is. I raised the mic element above the board with a piece of plastic tubing and this stopped the crosstalk hum completely. The tubing is 3/8 diameter X 7/16 H with a notch. It is attached to the ...

SD70MAC

You will need to put the green wire on battery and the orange wires is the one that goes to ignition.

Just checked with an W7 astro spectra plus in my office. Your problem should be fixed when you make the above changes.

Radio Kid

That sort of depends oh how the ignition jumpers are done inside ...

SD70MAC

Also another way to view the photos.

http://forums.radioreference.com/motoro ... ost1798620

SD70MAC

I been racking my brain to fix my W3's transmit hum and I finally found a way to fix it and here it is. I raised the mic element above the board with a piece of plastic tubing and this stopped the crosstalk hum completely. The tubing is 3/8 diameter X 7/16 H with a notch. It is attached to the board ...

SD70MAC

Can a second mic be added to the drawer unit on a low power Astro Spectra? It would be a regular mic. The HHCH has the hum, just wanting get around that issue.

SD70MAC

You will need to put the green wire on battery and the orange wires is the one that goes to ignition.

Just checked with an W7 astro spectra plus in my office. Your problem should be fixed when you make the above changes.

Radio Kid

Thanks to all . I have the wire routed to the right place now,I ...

SD70MAC

radiokid wrote:Is the Green wire to Battery or constant power and Orange wire to Ignition?

Both were together when I bought the radio, so they are both to ignition.

SD70MAC

Anyone got any pictues of this modifcation ? I need more info on this please..

SD70MAC

I have a W7 Astro Spectra remote mount that I finally installed and I have a probem with the Ignition sense. The radio will turn off when you turn off the ignition switch to the off position,but when you turn the ignition back ON you have to use the power button to power up the radio. What have I ...

SD70MAC

Try this:
CPS R06.09.06 @00248699h there should be 74. Change this 74 to EB and save.

This is from an old tread.

SD70MAC

I had this problem with my XTS5000, I replaced the display with a C04 display and it was fixed. Mine had a C02 display in it when I bought it and gave the same issue. I also had this problem with an aftermarket battery, the voltage would drop low on transmit.

Just my 2 cents

SD70MAC

That's what I thought, I just didn't want to feed voltage to the wrong place.
Thanks

SD70MAC

eurecomx wrote:test this one, for Mototrbo, is wires only.
eulalio

What pin on the Mobile does the USB pin 1 (+5 vots) go to,I just want to be sure.

SD70MAC

Thanks Steve !

SD70MAC · Re: Password for CDM1550LS Anyone found the password fix for CPS 6.12.05 yet ?

Anyone found the password fix for CPS 6.12.05 yet ?

SD70MAC

Check your PM'S

SD70MAC

If you do the Region code hack to your CPS you shouldn't have any problems.

SD70MAC

On the Pro Series radios you need to check the " Invalid Fields" before you close the codeplug ,this will help from getting the error you have next time. I have seen many errors like this over the years,it sucks when you have spent lots of time on it.

SD70MAC

Yes it decode and encode.

SD70MAC

Thanks

SD70MAC

What is the gauge of the wire on the High power Spectra power cable ?

SD70MAC

I have tracked it down to 1 zone ,it will work fine in the other Zones. Now I just have fine the frequency or frequencies that the radio don't like. Thanks Bruce for heading me in the right direction !

As far as the flash I cannot change that myself ,it always had this option since I had it .

SD70MAC

NSPD wrote:What firmware is this radio running?

FW 11.71.06
DSP 8.03.05
598008-0C0640-8

SD70MAC

I tested 2 35amp Astrons and they stayed in 13.7-13.8 range for 1 hour even when the Spectra powered off and on again.

Cecil,

I do have it programmed out of band below 146, I will remove the out of band frequencies and try that. That sucks to remove Ham stuff.
James

SD70MAC

I have an Astro Spectra W9 100w that will power off and back on from time to time,what would be causing this ? I resodered all power connections trying to find the problem ,but it still does it.

I would take a voltmeter and look close and hard at the ignition voltage feeding the radio. If it ...

SD70MAC

I have an Astro Spectra W9 100w that will power off and back on from time to time,what would be causing this ? I resodered all power connections trying to find the problem ,but it still does it.

SD70MAC

Looking to buy an XTS3000 403-470 UHF from someone, but the flashcode is 100004-000000-4 and only translates into Astro IMBE operation and H37 SmartNet systems operation. I'm not too familiar with how the flashcodes are laid out, but I need the radio to do full repeater PL mode for conventional HAM ...

SD70MAC

Motorola needs to get in gear and get support for 64bit computers for all current products. I would like to see how the " Talk Group to FPP " works in FPP.

SD70MAC

I have several CDM's VHF & UHF that are fw r5.08.02 and they all have 12.5,20,25 steps. Look at the model # of the radio when you read it with the CPS if it is for example M25KKF9DP6AN it will do all steps. If it is M25KKF4DP6AN it will only do 12.5 ! The "4" in the model# are 12.5 only radios. The ...

SD70MAC

It's been a little bit, but I am still trying to solve this issue. The main one I notice this on is my local PD channel, since they are the only ones nearby that are narrowband and use MDC. The other local PD, local EMS agencies, and a couple fire departments that use MDC are all wideband and I ...

SD70MAC

Thanks Al,that's what I needed.

SD70MAC

I have a PM400 and I cannot figure out how to remove "LTR Group 1" from the Channel position list,any idea how to do this ? I don't want to have that in the radio when you scroll through the channels,we don't use LTR anyway.

Where do you program the Ignition sense or is it not programmable like ...

SD70MAC

I bet it has 5.17 firmware ,if so you will have to get CPS 6.12.02.

Search found 377 matches