Unfortunately I do not have a good path between sites, Trees. Pesky critters. I will keep researching and see if we can figure this out.

Here is the whole story. If you can help, any and all is appreciated. We have 2 vhf Quantar repeaters in p25 That we would like to link via an unused 800mhz pair we have. We have 2 800mhz quantar repeaters, The orig idea was to link via v.24 between the vhf and 800 machines. This works on one end ...

Is it possible to interface a XTL5000 Consolette to a quantar via v.24 RT/RT? I need to link 2 VHF Quantars via 800 MHZ.

Karl NVW wrote:800 MHz Quantar was never offered with a control station frequency plan (Tx low), just as a repeater with Tx high.

What would you recommend to use as a remote base for 800mhz then any ideas? I am using p25

Looking for info on the upgrade (mtr2000 upgrade to mtr3000). The kits I am seeing now include the PA and make this not cost effective. Does anyone have the correct part number to make this cost effective?

Thank you for that info!!

Unfortunately that did not work. The modules seem to be out of range. Does anyone know the part numbers for the correct modules?

JeffFireRadio wrote:Have you installed the antenna switch kit to convert it back to a base station, programmed it as a base station (vice repeater) and then tried programming it with the frequencies you desire?

No that's a great idea!! I will give that a shot. thanks

Looking for info on linking 2 quantar repeaters onsite via v.24 and wireline. I see reference to a rt/rt but links are dead. Is this as simple as a shielded cat 5 cable to the v.24 ports? Any help appreciated. There does not seem to be info in the service manual I have. Thanks

Wanting to use a 800 MHz quantar repeater as a remote base. Problem is one of the channels needs to be a repeater channel. How do you go about reversing the frequencies in that unit. In the 800 MHz Quantar they seem to only let you tx in high 800mhz portion, and RX in the low 800 MHz portion. I need ...

on the advice of a very smart man. On the new radio that I got I programmed it and had it functioning. Then I went ahead and cloned it to this radio and now I have another 1225 that is functioning. So cloneing instead of writing fixed this situation.

A good point was brought up by a fellow member. How often are the fans on these supposed to run? I looked through the service manual and did not find an answer. Does the FF have something to do with the cooling fan? Would that affect programming?

Ok Here is what we have. The rss, cable, and computer all seem good as it did upload the codeplug to the other GR1225 repeater and it works fine. So does anyone have any ideas how to deal with the other repeater? The only diff between the two repeaters are one is VHF (this one currently functions ...

Ok Just read another gr1225 Have no trouble editing saving or reading this codeplug. I have not tried to write it to the radio as I do not want to cause harm to another repeater. Just some more fyi. Hope someone reads this that has had similar issue.

version 4.0 rss Pentium 111 comp running xp. It reads other gr1225's and lets me look at there info. Till I find out why this display went to FF and what happened I will not try to write to them tho. I do not believe it is the Rss as it acts fine after reading another radio.

The error I get is 1225 series rss
Runtime error "381":
Invalid property array index
Exactly as it reads sorry was gone for a couple weeks
When I try to write orig back I get product line mismatch operation was aborted.


Any help would be great thanks

Yes I can read it. But cannot look at info. When I go to look at tab it just gives me an error prompt. I really hope I have not bricked this....

Anyone have any ideas I tried the channel up-dn together for 5 sec no results. Just beeps. Anyone know how to do a reset on this radio? Thanks

GR1225 with FF on display.
As the title reads. I wrote codeplug to radio and FF ended up on display. Will let me read the radio but it will not let me go in and rewrite with orig codeplug. Have researched and searched all I have found that means is it did not exit programming correctly. Anyone have ...