Search found 137 matches
- Thu Jun 13, 2019 8:31 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: remote radio via cisco routers..
- Replies: 122
- Views: 90177
Re: remote radio via cisco routers..
To dig up an old thread, Does anyone have 2 working configs I can dumb into some routers and use, I have a need for a tone remote to control an offsite repeater over a ubiquiti link its about 1500 ft. I can get whatever E/M cards and routers that you have this working on but I have read this thread ...
- Tue Dec 18, 2018 8:26 am
- Forum: Consoles
- Topic: Avtec or Mcc7500 Console and Cisco 8851 Phones
- Replies: 2
- Views: 5741
Avtec or Mcc7500 Console and Cisco 8851 Phones
Anyone have any experience hooking up Cisco IP phones to a Avtec or Motorola Console for Headset audio Customer is in process of obtaining one of the 2 above coneolse and has asked us to interface the headsets to both the radio and Phone I have done this in the past with Centracom and Cassidian Phon...
- Wed Feb 28, 2018 2:04 pm
- Forum: Consoles
- Topic: MIP5000 Audio Recording
- Replies: 1
- Views: 5993
MIP5000 Audio Recording
Has anyone used a IP recorder for a MIP5000 Looking at picking up the RTP streams to go to the recorder via multi cast I see my channels RX audio on 235.0.1.2 RX Channel 1 50004 RX Channel 2 50008 But the TX seems to be on 50000 but its common to every channel ie if Im on Channel 2 talking the TX au...
- Fri Feb 09, 2018 10:13 am
- Forum: APX Series Subscribers
- Topic: APX4500 Igntion trouble
- Replies: 3
- Views: 7613
APX4500 Igntion trouble
Have a APX4500 800 Mhz Firmware 16.23.00 When you apply power without ignition the Control head goes into a loop where it will flash APX4500 for a few secs you hear a small blip from speaker and then it starts over. When you apply ignition the radio boots up and works as it should whenyou remove ign...
- Tue Jun 28, 2016 10:33 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: Quantar / Astotac vhf p25
- Replies: 2
- Views: 2271
Re: Quantar / Astotac vhf p25
Thanks for the info Astro Spectra, I have found very very few pieces of anything VHF rcvr only,
I figured the quantar would work with the v.24 card since it works at the main/prime site
I figured the quantar would work with the v.24 card since it works at the main/prime site
- Tue Jun 28, 2016 7:37 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: Quantar / Astotac vhf p25
- Replies: 2
- Views: 2271
Quantar / Astotac vhf p25
Have a question for the quantar astrotac guys Have a 3 site vhf p25 conventional Main TX Site IS Co-located with the comparator Site 2 and 3 are AstroTac Rcvr's with the V.24 data running thru some Cisco Routers and then thru a Cambium PTP link back to the main Site. The Customer is wanting to add S...
- Fri Mar 11, 2016 10:24 am
- Forum: ASTRO25 Series (XTS/XTL 1500/2500/5000) Subscribers
- Topic: XTL1500 Rcv Help
- Replies: 0
- Views: 5827
XTL1500 Rcv Help
XTL1500 UHF Help Have a XTL1500 UHF P25 that having an odd issue I have one channel 453.2375 458.2375 NAC 375 that I can transmit on but it will not rcv back from the repeater. I can program a portable to key the rptr output and the radio will rx and it will rx and tx on direct. It will RX and TX on...
- Wed Jul 15, 2015 6:39 pm
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Mototrbo system
- Replies: 5
- Views: 8733
Re: Mototrbo system
Did you give each raido an individual ID that will happen if each subscriber doesnt have its own ID
- Wed Jun 17, 2015 8:39 am
- Forum: Consoles
- Topic: MIP5000 Audio Question
- Replies: 3
- Views: 7236
MIP5000 Audio Question
Have a 7 channel MIP5000 2 digital consolettes and the other 5 channels are tone it is setup with primary channel on select speaker on digital 1 monitor speaker 1 is diagital 2, mon spkr 2 is analog 1 mon spkr 3 is analog 2 mon spkr 4 is analog 3 and other 2 channels go to unselect speaker the issue...
- Fri Feb 06, 2015 12:27 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: MIP 5000 Network Connectivity
- Replies: 8
- Views: 10849
Re: MIP 5000 Network Connectivity
Sonic Wall Been down that road and never got them to work reliably switched over to cisco gear and been working flawless
I noticed in the dcpm the audio ports would turn red after a few minutes on the sonicwall while the rtcp ports would stay open
I noticed in the dcpm the audio ports would turn red after a few minutes on the sonicwall while the rtcp ports would stay open
- Sat Jan 24, 2015 7:47 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: MIP 5000 No RX Audio
- Replies: 2
- Views: 2219
Re: MIP 5000 No RX Audio
did you setup the jackbox in control panel ?
- Fri Dec 12, 2014 5:39 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: [Relocating Gold Elite Op Positions away from CEB]
- Replies: 10
- Views: 3816
Re: [Relocating Gold Elite Op Positions away from CEB]
Do you really want to go through all this for an outdated and soon to be a non supported product if you haven't already got the word? The cost could be put towards a currently supported product line that has many years of strong support still available. Jim DO I want to do this NO, but do I really ...
- Thu Dec 11, 2014 1:48 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: Anyone Running MIP5000 Got a solution for POwering gateways
- Replies: 3
- Views: 2380
Anyone Running MIP5000 Got a solution for POwering gateways
Anyone else running MIP5000 came up with a solution to running the Gateways other than the standard power brick
Would like to find a power supply that could run multiple gateways instead of needing 20 power chords and tons of wires and power bricks to deal with
Would like to find a power supply that could run multiple gateways instead of needing 20 power chords and tons of wires and power bricks to deal with
- Thu Dec 11, 2014 1:30 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: [Relocating Gold Elite Op Positions away from CEB]
- Replies: 10
- Views: 3816
Re: [Relocating Gold Elite Op Positions away from CEB]
Yeah, I have messed a lot with centracom but never remoting op positions and appreciate the help SO the cie to ceb link I guess you could do that with some e&m for select/unselect/grnd/mic probably don't need monitor 1 and 2 and then just need the Ethernet connection for the pc back to the main ...
- Thu Dec 11, 2014 1:00 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: [Relocating Gold Elite Op Positions away from CEB]
- Replies: 10
- Views: 3816
Re: Centracom gold elite
Thaks for the reply alex This is probably a bit of a tall order because you have to find parts. The easiest way is probably to get 3 card cages (since you can only have two OP's per cage. Then get an AMB card for each CEB. You will need an Ambassador which would have a T1 to each CEB. Wouldn't the A...
- Thu Dec 11, 2014 12:21 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: [Relocating Gold Elite Op Positions away from CEB]
- Replies: 10
- Views: 3816
Re: [Relocating Gold Elite Op Positions away from CEB]
The controller and the ceb are collocated so no t1's there
- Thu Dec 11, 2014 11:15 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: [Relocating Gold Elite Op Positions away from CEB]
- Replies: 10
- Views: 3816
[Relocating Gold Elite Op Positions away from CEB]
SO I have a customer running a smartnet system with a 5 position gold elite that is looking to relocate there gold elite offsite from there current location which is co-located with the Ceb and smartnet system There current setup is mixed mode so they have 13 DIU's that are talking to the quantars a...
- Mon Nov 10, 2014 5:13 am
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Cap plus trunking issue
- Replies: 19
- Views: 6626
Re: Cap plus trunking issue
com501, Correct
so as far as the udp port jsut make them 50000, 50001, 50002
will try that today and see what happens I can say so far that capacity plus is not very stable, like connect plus much better but the cost of the controller is crazy
so as far as the udp port jsut make them 50000, 50001, 50002
will try that today and see what happens I can say so far that capacity plus is not very stable, like connect plus much better but the cost of the controller is crazy
- Thu Nov 06, 2014 7:11 am
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Cap plus trunking issue
- Replies: 19
- Views: 6626
Re: Cap plus trunking issue
upgraded to 2.30.20 Still having a few small issues for some reason if you busy out all the time slots currently 6 unkey one subscriber and try to key up it will not let you use that 6th time slot until another radio unkeys and there are 2 free slots Can someone confirm my settings Link establishmen...
- Thu Sep 25, 2014 5:50 pm
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Cap plus trunking issue
- Replies: 19
- Views: 6626
Re: Cap plus trunking issue
so for a 4 repeater setup what would you suggest for the repeater addresses
as far as ip's and id's
as far as ip's and id's
- Fri Aug 29, 2014 9:16 am
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Cap plus trunking issue
- Replies: 19
- Views: 6626
Re: Cap plus trunking issue
Yeah I called Motorola to see what they had to say they went through programming and said it all looked good and of course blamed in on the switch, I told them I tried a crossover cable as well and had the same result I am running RDAC on the system right now to see if when it quits it shows anythin...
- Fri Aug 29, 2014 3:33 am
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Cap plus trunking issue
- Replies: 19
- Views: 6626
Re: Cap plus trunking issue
What is the master ip address? Master IP is 192.168.1.1 peer is 192.168.1.2 point to 192.168.1.1 on port 50000 one question I do have on the UDP ports does each rptr gets its own UDP port so master is 50000 all peers get master udp set to 50000 then there is another udp port box should those be the...
- Thu Aug 28, 2014 5:16 pm
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Cap plus trunking issue
- Replies: 19
- Views: 6626
Re: Cap plus trunking issue
WEll Spoke to Soon, Still having issues, Noticed in RDAC that when I have the issue that the peer does not show up you reboot the master reconnect and the peer is present I switched the repeaters around so the peer is now the master and get the same error I have tried 3 switches one being the Motoro...
- Thu Aug 28, 2014 11:05 am
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Cap plus trunking issue
- Replies: 19
- Views: 6626
Re: Cap plus trunking issue
haven't swapped the repeater and so far its still working going to install next week after it burns in over the holiday and we shall see how it goes
- Sun Aug 24, 2014 12:49 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: v.24 transport over ethernet
- Replies: 38
- Views: 23778
Re: v.24 transport over ethernet
well I was able to get this going,
Ended up using the 2811 ISR with the cards and the Enterprise base software for the 2811 and STUN
Easy setup using stun and so far working good,
Was never able to get the pseudowire class stuff to take but STUN is working great
Thanks for the Help ALEX
Ended up using the 2811 ISR with the cards and the Enterprise base software for the 2811 and STUN
Easy setup using stun and so far working good,
Was never able to get the pseudowire class stuff to take but STUN is working great
Thanks for the Help ALEX
- Sun Aug 24, 2014 5:58 am
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Cap plus trunking issue
- Replies: 19
- Views: 6626
Re: Cap plus trunking issue
WIll try that, Left the system running at the office over the weekend will check it Monday to see if its still trunking and if not ill swap them around
- Fri Aug 22, 2014 7:37 am
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Cap plus trunking issue
- Replies: 19
- Views: 6626
Cap plus trunking issue
Have a fairly simple setup for a cap plus trunking 2 rptrs on firmware r02.30.02 when you first turn them on they appear happy and the trunking takes place as normal after an hour or so its like the master and peer quit communicating and the only traffic that will work is on the master rptr I have t...
- Mon Aug 18, 2014 11:17 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: v.24 transport over ethernet
- Replies: 38
- Views: 23778
Re: v.24 transport over ethernet
Alex,
are you familiar with how to set these 2811's up,, these are the first to i ahve seen and lost as ever at how to set them up
are you familiar with how to set these 2811's up,, these are the first to i ahve seen and lost as ever at how to set them up
- Fri Aug 15, 2014 3:41 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: v.24 transport over ethernet
- Replies: 38
- Views: 23778
Re: v.24 transport over ethernet
Parts are ordered see how it goes
- Thu Aug 14, 2014 9:17 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: v.24 transport over ethernet
- Replies: 38
- Views: 23778
Re: v.24 transport over ethernet
i don't see the cards that cheap anywhere you got a source to find them for 20 dollars I see them for 125 to 175 each
- Wed Aug 13, 2014 6:52 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: v.24 transport over ethernet
- Replies: 38
- Views: 23778
Re: v.24 transport over ethernet
Alex thanks for the info, Heard from Rad they cant supply the parts to get me back running so down the cisco rode I go I have one more and hopefully the last question They list a HWIC-1SER and a HWIC-2SER if I went with a 1861 and a HWIC-2SER at the main site and a 1861 with a HWIC-1SER at the remot...
- Tue Aug 12, 2014 12:31 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: v.24 transport over ethernet
- Replies: 38
- Views: 23778
Re: v.24 transport over ethernet
Yeah that would be great if you can get me those numbers for the cable its on a closed PTP wireless network so no VPN needed just need something to replace these rad boxes with Im hoping rad will come up with the 2 parts I need to get this going again , but want to have an option ready need to get t...
- Tue Aug 12, 2014 10:18 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: v.24 transport over ethernet
- Replies: 38
- Views: 23778
Re: v.24 transport over ethernet
Yeah alex we have the rad products in service now but they have quit
what cisco gear are you using
what cisco gear are you using
- Tue Aug 12, 2014 8:12 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: v.24 transport over ethernet
- Replies: 38
- Views: 23778
v.24 transport over ethernet
anyone got any suggestions on v.24 transport over Ethernet for a p25 voting system have had the system in service for a few years and now one of the RAD SPS-3S modems has went bad and Motorola and the Vendor Rad Data no longer sales or supports these modems so there are no parts available so looking...
- Thu Apr 10, 2014 6:21 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: PTP600 failure, appears to be corrosion inside
- Replies: 23
- Views: 6810
Re: PTP600 failure, appears to be corrosion inside
Had this happen on several PTP300 units, we fixed the issue by taking the units apart and usign the black form a gasket stuff for cars gaskets to seal the units and so far so good after 9 months no more failures cambium told us it was faulty install on the antenna cables as well but since the dish i...
- Wed Mar 19, 2014 5:57 am
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: xpr4000/5000 series Problem
- Replies: 0
- Views: 1990
xpr4000/5000 series Problem
Anyone had any luck tying a desk mic to the rear accessory connector on the 4350/4550 or 5550 we have a couple of control rooms that have 3 desk mics currently connected to a cdm1250 that company is fixing to upgrade to a trbo connect plus system and we have had issues in other areas tying desk mics...
- Wed Mar 05, 2014 5:41 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: MTR3000 and SNV-12
- Replies: 8
- Views: 2975
Re: MTR3000 and SNV-12
when the pilot tone drops it generates a ground on the PTT line on the back of the mtr3000 so i guess that would be e&M
- Fri Feb 28, 2014 4:44 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: MTR3000 and SNV-12
- Replies: 8
- Views: 2975
Re: MTR3000 and SNV-12
the snv-12 does drops the keying the links are done via RF and pilot tone and they are not dropping you can locally key the mtr3000 until the time out timer kicks in and it has no issues i spoked with raytheon earlier and they advised to reseat the cim-2a card next time without power cycling and see...
- Fri Feb 28, 2014 4:59 am
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: MTR3000 and SNV-12
- Replies: 8
- Views: 2975
MTR3000 and SNV-12
ANyone have much experience with a SNV-12 Voter tied to a MTR3000? Have one thats been in service for about 15 months was moved about 7 months ago from one Tower site to a water tank about 2 miles down the road since it was moved we are having issues with the SNV-12 just locking up or stopping worki...
- Thu Nov 14, 2013 7:07 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: Centracom Gold Elite
- Replies: 9
- Views: 2364
Re: Centracom Gold Elite
Yeah i ahve the necessary windows version and software, and was able to find a coim with correct firmware waiting on other parts to come in and should install in a couple weeks what i was wondering was liscense fee's I figured "M" would have had somehting in the server software that had to...
- Mon Oct 28, 2013 3:03 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: Centracom Gold Elite
- Replies: 9
- Views: 2364
Re: Centracom Gold Elite
As i suspected, No support from Motorola on the centracom gold elite
only thing the tech said was to make sure the coim has the same firmware that we had,
so I guess there arent any other requimrents for software which was my main concern
now to try and track down enough parts
only thing the tech said was to make sure the coim has the same firmware that we had,
so I guess there arent any other requimrents for software which was my main concern
now to try and track down enough parts
- Sun Oct 27, 2013 4:27 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: Centracom Gold Elite
- Replies: 9
- Views: 2364
Re: Centracom Gold Elite
Yeah i have opened up a request on MOL but I doubt they will do anything as they dont sale the product anymore
- Fri Oct 25, 2013 12:02 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: Centracom Gold Elite
- Replies: 9
- Views: 2364
Centracom Gold Elite
Anyone know on a gold elite since Motorola no longer sales or supports them what I would need to add another position to our current 5 position system
I know the physical hardware, COIM, CIE, computer monitor and such, But is there any software restrictions that will hold me up??
I know the physical hardware, COIM, CIE, computer monitor and such, But is there any software restrictions that will hold me up??
- Thu Oct 24, 2013 7:20 am
- Forum: MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- Topic: Trbo XPR6100 Parts Question
- Replies: 2
- Views: 1881
Trbo XPR6100 Parts Question
Anyone got any part numbers or had any luck ordering the Flex and sticker for the Accessory Connector for the XPR6100 series I have several 6100's that the accessory connectors is corroded and need to replace but BIG M says the 2 parts are not available I cant find them in the basic or detailed manu...
- Thu Sep 26, 2013 5:13 pm
- Forum: Legacy Batboard Motorola ASTRO (VSELP/IMBE/AMBE) Equipment Forum
- Topic: O9 l/s control and ign switching
- Replies: 9
- Views: 3723
Re: O9 l/s control and ign switching
U may have already found your answer but you can program the 7500 with a timer to stay on after it loses ignition so if you need light sto stay on it can follow the timer
- Mon May 06, 2013 12:36 pm
- Forum: General Motorola Solutions & Legacy Radio Discussion
- Topic: Question On Archives and COmputers
- Replies: 4
- Views: 2053
Re: Question On Archives and COmputers
what software are you using to sync we have a server so thats not an issue i jsut havent found a sync software that wants to play nice with M software like I posted Google Drive works great keeping the files updated but you cant open them in software. If i move the files from teh google drive folder...
- Mon May 06, 2013 10:01 am
- Forum: General Motorola Solutions & Legacy Radio Discussion
- Topic: Question On Archives and COmputers
- Replies: 4
- Views: 2053
Question On Archives and COmputers
Not really what section to ask this so if this is wrong please move, Trying to come up with a simple solution for Archives, Currently we have 2 programming PC's at our office setup fulltime, then all techs carry laptops and store archives on them, I am trying to come up with something to keep all th...
- Sun Mar 17, 2013 4:28 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: Tower lighting Issue
- Replies: 6
- Views: 1414
Re: Tower lighting Issue
Sorry Been Busy, Its a incadescent tower light ran in conduit, the noise is only there when the light is lit, we have moved the RX antenna down the tower 50 ft below the light and its still there, Our next option is going to mount the RX antenna on the roof of the buidling and see if there is noise ...
- Thu Feb 14, 2013 1:01 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: Tower lighting Issue
- Replies: 6
- Views: 1414
Re: Tower lighting Issue
Will look into the type of cord not for sure I think its in conduit and the controller im unsure on are you saying to put the ferrite cores on the power wire where it comes out of the controller to go up the tower What type of controller is being used to control the lights? If by some chance the lig...
- Tue Feb 12, 2013 12:56 pm
- Forum: Base Stations, Repeaters, General Infrastructure
- Topic: Tower lighting Issue
- Replies: 6
- Views: 1414
Tower lighting Issue
I have a tower with a UHF RX only antenna mounted about 10 ft away from a TDR Incadescent side beacon light on a rental tower The issue anytime the beacon flashes it wipes out the signal coming into the UHF antenna The tower owner has changed the bulbs with no help and TDR is saying they have nerver...