Batboard

fineshot1

I just stab them with 12 volts for a few seconds from the closest Astron PS. Then the Impres charger can properly charge them. GARY. That may not be such a good idea Gary. These impress batteries contain charge rate electronics that may be damaged by doing that. Many years ago with regular nicad ba...

fineshot1

I just stab them with 12 volts for a few seconds from the closest Astron PS. Then the Impres charger can properly charge them. GARY. That may not be such a good idea Gary. These impress batteries contain charge rate electronics that may be damaged by doing that. Many years ago with regular nicad ba...

fineshot1

I could not find any online info regarding impress charger charging contacts so I disassembled my only impress charger and the contacts were labeled on the pcb " B+ TH CD B-" so I suspect that the one labeled as CD stands for charge data which would be the data read from the battery by the...

fineshot1

Hi, everyone. I've got some NOS NNTN6034A batteries that are apparently so low in voltage that the IMPRES charger won't actually initialize them. I've tried a bunch of times so far but each of the batteries goes from steady flashing yellow for a few minutes to rapid flashing red. I've read that if ...

fineshot1

Yes - I have seen this before very low in the vhf-hi band spectrum. In general maxtracs do not perform well in that low of vhf-hi spectrum and sorry but i have no suggestions for you in this regard expect that their is most likely a solution on perhaps one of the maxtrac websites perhaps on the yaho...

fineshot1

Just my opinion but a pair of known good car type batteries in parallel with a solar battery charger would be a good start with the solar charger keeping the batteries topped off. PS - The battery box would of course have to be for outdoor use and weather sealed. Note: You did not say whether these ...

fineshot1

Unless you have some sort of test jig from motorola that I do not know of the only way that I know of to test them is in the radio they were designed for. As far as determining the frequency read the Khz on the crystal itself and use the models crystal calculation mathmatics to determine the channel...

fineshot1

I did this once about 35 or 40 years ago for a friend with a VHF Hi band MT500 portable and
the channel elements are so tiny it is very difficult with good vision but if your vision is as
bad as mine is these days there is no way I would even think about attempting it.

fineshot1

The all band antenna shipped with the APX8500 is a QMA. I just made a pair of patch cables from QMA to N for wattmeters and testing, and gave a set to each tech and installer. Yeah, it's a PITA, but I haven't see an adapter kit that has them - yet. We have not purchased any lately so I have not see...

fineshot1

Wrong direction. I need the QMA antenna cable to mini UHF adapter. Can't find it anywhere. Makes wattmetering installations impossible. What I posted above is what we use to adapt our APX8500 QMA connectors to mini-uhf connectors that are supplied by motorola so what about these is WRONG? With them...

fineshot1

Why QMA to Mini-UHF? Do you have Mini-UHFs on your meter? Our wattmeters have N connectors and we use QMA to N for testing, cable type from wattmeter to radio, adapter from antenna to wattmeter. [removed - keep it civil please. -Alex] We made a variety of patch cords for every possible need and the...

fineshot1

Wrong direction. I need the QMA antenna cable to mini UHF adapter. Can't find it anywhere. Makes wattmetering installations impossible. What I posted above is what we use to adapt our APX8500 QMA connectors to mini-uhf connectors that are supplied by motorola so what about these is WRONG? With them...

fineshot1

QMA TO MINI-UHF ADAPTER CABLE
Manufacture Part Number = 095-668-50065
Customer Part Number = CB000091A03

fineshot1

1. Do you have the codeplug password protected? If so enter the proper password.
2. You may have to setup the personality for this channel for narrow band.
Hopefully that covers it - if not perhaps someone else can can come up with the solution.

fineshot1

Even if you could do so - why would you need to do that?

This type of mobile radio is NOT made for 100% duty cycle and this would likely burn it up sooner or later.

fineshot1

As far as i know - SP has always meant = "Special Product".

fineshot1

This is very doubtful.
APX CPS is very bloated as compared
to the Astro 25 Mobile or portable CPS.

fineshot1

Just remember to remove the oem console mounting base plate after removing the oem console
and mounting the Havis console instructions doc should be followed and you should be ok.

fineshot1

The industry standard charging voltage is "14.2" VDC for most applications.

fineshot1

The only 'oddball' quantars that I am aware of were the data stations. These were for slow speed data transfer only. I believe they were using them in Ohio for the MDT's in the OSP cars for looking up license plates. There were a number of them in place when MARCS was still running the 3.5 system. ...

fineshot1

Hi, Gang! In addition to charging the battery, does the NNTN7624 APX8000 mobile charger also support monitoring the radio's receive audio via the radio's internal speaker, whilst simultaneously charging in the pocket, or is it meant to be used ONLY for charging? The Motorola User Guide alludes to t...

fineshot1

It took me awhile to find it but To answer the OP's question see below: The word "swap" in his original post had me going in the wrong direction. I missed that his radio was already a remote mount. Sorry for the confusion. PMLN4958 O3 handheld control head 17-foot extension cable. Connects...

fineshot1

Conversion kit? They are supposed to be plug and play. Its a blue connector into the TIB. NOT if you are migrating from one control head to another! Have another coffee and wake up and go back to the top OP's post. Conversion kits are required to replace the ribbon cables in the TIB and CHIB in man...

fineshot1

I am trying to swap an O5 head to an O3, but whenever I plug it into the TIB the radio shuts off. I thought the CH Synch was the issue but it will not allow me to plug in the O3 head during the process. Running fw r20.50.05 dsp 19.50.01 XTL5000 remote mount. Works fine with the O5 head. BTW I even ...

fineshot1

This is what I came up with for an APX7000 but there may be one missing here or there. Comments and suggestions are welcome. XE Remote Speaker Microphones NNTN8575A Xtreme Temperature Cable High Impact Green Housing NNTN8575ABLK Xtreme Temperature Cable Black Housing NNTN8575AYLW Xtreme Temperature ...

fineshot1

Karl NVW wrote: ↑
Sun Oct 18, 2020 9:06 pm
That one did not ever exist for NAmer.

Karl - I know that - it was just being used as an example!

fineshot1

Sounds like you may have a high level of noise on any memory channel.
Have you checked your home for noise sources ?
Try again away from your home like out in the middle of a parking lot
where there could be no noise source.

fineshot1

My question is in respect to the North American Region.
Anyone know of any oddball quantars? For instance a
220Mhz quantar for the NA region would be an oddball.

fineshot1

Sorry - I can't help you. I do not know if this jumper was an option or not
and I could not find any doc's on this mic.

fineshot1

If you PM me with your email I can send you a pic with the mic circuit board jumper

fineshot1

If you are looking for hard copy docs from moto your way too late. This is equipment that has not been offered for sale for a long time now.
Why don't you just download what you need from here:

http://www.repeater-builder.com/motorol ... intro.html

fineshot1

All, Been a while since I've been here! Site looks great! Got a question... I need to replace the Rubber Antenna on my HT 1550 XLS H25SDN9DU8 It seems to have become brittle and just fell apart. Hey Gig - If you have the whip model antenna the part number = NAE6483. The rubber whips becoming brittl...

fineshot1

have you confirmed that the frequency standard output is reaching the panel buttons logic circuit?
I ask cause it sounds like the panel buttons logic is not working.

fineshot1

Is the system reboot something you do inside the recorder or something you do with a programming computer? Omnicron Electronics make its own voice logging recorder equipment and applications used with this equipment so the reboot would most likely be on this equipment or applications much depending...

fineshot1

I was able to get voice mail once. Other times it was full. No return call. This recorder got a power surge and display is lite up blue, but no letters or numbers. Inside unit there are 5 LED's. One is lite blue. The others are off. I can hear the hard drive running. Is there a reset? If all else f...

fineshot1

If there is a list of antenna for the XPR series portables can someone plz list it?

fineshot1

Not even sure how you would be able to program that in via the cps programing software
since it is NOT on a valid 12.5Khz boundary.

fineshot1

Jim Thanks for the explanation. My confusion is, when I create a 2nd scan list (for another zone) how do I associate that list with the new zone? When I select the 2nd zone, is the radio going to search all scan lists and see if any of the channels are included in the scan lists I created? The scan...

fineshot1

PETNRDX wrote:I just googled "Motorola radius M-10" and the first seven hits show the M-10.

Since the OP did not ever use the dash like you did I did not search with the dash.
What the OP shows above = "Motorola Radius M10 UHF radio"

fineshot1

PETNRDX wrote:The M-10 is a single freq low tier version of GM-300.

Google search after google search showed up ZERO on the Radius M-10 hence my post above.

fineshot1

Good Morning, I have a question regarding a Motorola Radius M10 UHF radio. I can connect to the radio and successfully read the code plug and even write a new code plug to the radio, but the radio dose not RX or TX It did work at one time and I can not remember what happened, It may have been due t...

fineshot1

You will need these below pins and removal tool but not even sure if these parts
are still available.

Contact Pin Removal Tool part number - 66-84690C02 and Contact Pins (package of 5) - part number 09-84151B03

fineshot1

I must assume you are referring to the PLN7737 HHCH.
The answer is no - just program the radio as you would
normally do.

fineshot1

John Thank you this is correct, howewver the clip on the radio side is broken off as well. I am going to try to do just that replace the housing and get the clip on the radio back on. I may be able to get a 3k to see if I can get a few clips off that if they are the same size. Thank you Chris This ...

fineshot1

Try Smiley - they may have what you need

https://www.smileyantenna.com/

fineshot1

miamiwise wrote:Hi Fineshot1

Do you have any suggestion of service places located in Los Angeles or San Diego CA ? Thanks.
Derric

No I do not - I live in NJ and have no idea of what is available in CA.

fineshot1

Can anyone recommend a service facility to repair a sick 1900 CSA? Won't lock on frequency, frequent & various warnings. Try this facility - i have had very good experience with them fixing my 1900csa Alltest Instruments, Inc. 500 Central Ave. Farmingdale, NJ 07727 Ph: 732-919-3339 Fax: 732-919...

fineshot1

many of these vhf low profile antennas on a fiberglass roof require a ground plane under the installation area in order for the antenna to radiate properly. before you start any work read the installation doc as this should be pointed out in this doc. I have seen some of them that are tunable that n...

fineshot1

i have had this happen also and was told some where on the back of the TFT display are some configuration jumpers that sometimes oxidize over a period of time. After I pulled off the jumpers and re-installed them in the same place all came back to order with the display. Doing this excersize removes...

fineshot1

Karl NVW wrote:If your spanner tool is known to be newer than HT200 / HT220 portables (early 1970s), it could also be for MT500 or HT90/440 a decade later.

I have no information on this spanner and no way to know that

Search found 967 matches