Batboard

Haloncloud

I'm in need of MCS2000 Model 2 DOS Archive Codeplug for M# M01KHM9PW5BN . If Anybody can help. Thanks

Haloncloud
David

Haloncloud

Looking for schematic for Smart RIB. Trying to repair RLN1015D.

Thanks, Haloncloud

Haloncloud

This weekend Sunday the 20th is the Richmond, Va. Frostfest. Some Bat members will be in attendance. We will be operating two portable repeaters onsite if you would like to try them out. Also will be monitoring simplex Astro frequency. We will be located at the Central Virginia Radio Enthusiast ...

Haloncloud

If you can't get them from Motorola you might want too try McMaster-Carr. I have gotten stuff from them before. Not factory but close.

http://www.mcmaster.com/

David

Haloncloud

Will,

Even if the radio has 5 pin and 16 pin logic board what would be the difference you are still connecting to the same points in clamshell connector for Ground, Mic Hi, PTT on Maratrac radio ?

Haloncloud

Haloncloud

Using a Maratrac for a Transmitter is pretty straight forward.

-Open up the connector on Maratrac.
-Remove all wiring that connects to Radio Plug except the large Red and Black. (Power)
-Wire jumper from Pin 19 to Pin 4 in connector. (Pin 4 powers radio up)
-Wire jumper from Pin 17 to Pin 13 in ...

Haloncloud

I want to share pics and get some feedback on this portable repeater.

It's made in an audio case, and the panels are custom built for the various radios. It was built over the last several months by myself and batboard member Jay.

Comments, questions, etc appreciated.

http://www.fieldcomm.org ...

Haloncloud

Does anybody know if there is some kind of image burned on the U4, 24C16 chip for a T3011BX to DX upgrade? Motorola wants around $35 for this chip but I can get one for 2-3 dollars from electronics store.

Haloncloud

David

Haloncloud

I did as Nand suggested and used Pin 4 programmed (the alarm output) as COR for the COS connection on the VA3TO. Have had Echolink up and down in test mode and has been working great. Hopefully have it up and running full time in the 30days.

Haloncloud
David

Haloncloud

Nand,

Do you think if I built a voltage regulating circuit using a 7805 volt reg. to take my 12V to 5V would this work or would I be better off with the Relay?

Haloncloud

Haloncloud

I’m interfacing to a VA3TO controller for Echolink and I can’t get the COR to work and from what I can tell I need 5V I know it’s not much difference 4.5v to 5v but it does say 5V min.

Haloncloud

Haloncloud

I was wondering if there is a way to increase the voltage of the COR Pin 8 on a Maxtrac ? It is now 4.5V and I need +5V.

Thanks
Haloncloud

Haloncloud

I was wondering what size battery will work with the Astro Vehicle Adapter (Convertacom) ? or does it have adjustment. Looking to purchase some new batts for my Astro Saber and planning on purchasing a AVA also soon didn't want to mess up and have wrong batteries.

Haloncloud
David

Haloncloud

Run the FCC ID on this page might give you the info you want. https://gullfoss2.fcc.gov/prod/oet/cf/e ... Search.cfm

Haloncloud

Haloncloud

Just thought I would post this up for install group. Has some intresting Crown Vic stuff.

http://www.wattco.net/diagramscrnvic.htm

Haloncloud

Haloncloud

Problem: Using Maratrac as TX radio for repeater and will not TX PL. Here is info on setup, GM300 (RX) to I20R to Maratrac (TX). I have tried programming the PL into the radio and still will not TX PL. I have even just used Mic in programming port and still no TX PL. I am not using the control head ...

Haloncloud

I was planning on the same project several months ago but never had gotten it started. Since I couldn't find any Motorola docs on the RICK that seem to cover what I wanted to do I start mapping out the RICK Acc. connector and this is what I came up with. I'm not sure its 100% correct but hopefully ...

Haloncloud

The error message is: Write Device Failed The radio gives two high tone and goes silent. Once I click ok it goes back into steady tone.

Haloncloud

Haloncloud

I have an HT750 VHF that emits a steady beep to be best described. I get power up double beep and light, but then goes into steady tone which sounds a little garbled. I can read code plug but get a write error when trying to write to radio. Radio does not TX. A little background. Radio was on my ...

Haloncloud

I’m looking for any suggestion on a good in vehicle charging system for HT750 batteries. I need something that positive locks battery in place. That charges and conditions battery. System can be AC or DC. I have a job to replace the current charging system on HAZMAT unit which is just desktop ...

Haloncloud

Here is a link to my 2000 Toyota Tundra install that I just completed. Installed is a CDM1250 UHF, Kenwood TM-D700 and GPS. Console was custom built by me. Phase 2 will be to add CDM1250 VHF and Phase 3 is XTVA for my XTS3000.

http://home.comcast.net/~haloncloud/Tundra.htm

Haloncloud

Haloncloud

OK, Monty and Rapidcharger thank you for your opion on building a repeater but I already know how and the importance of using good components . My question was about the Zetron Model 38 not on what I needed to build a repeater. I will take the first tip and order the Manuel from Zetron. All I wanted ...

Haloncloud

Im looking to build a repeater and want to have mult. PL. I'm going to use two GM300 for my TX,RX . Has anyone used the Zetron Model 38 as there controller and what do they think. Easy of programming, Hookup and that kind of stuff.

Thanks,

Haloncloud

Haloncloud

I have roof mount NMO and glass mount ant. As for performance I am just as happy with my Glass mount as NMO roof. As for glass mount I'm going to recommend the Larson line they have several diffrent setups UHF, VHF and Dualband. I use the Dualband on my truck and have had a antenna analizer on it ...

Haloncloud

Would a cross-band repeater setup work for you? Lets say your simplex fireground is on VHF then link to UHF and transmit back to Dispatch using a beam type antenna. This could pose a problem with frequency allocation in your area but it might be all you need. The remote site setup would be minimal ...

Haloncloud

Anyone looking for the BC785D or BC250D might also want to contact Hobby Radio Stop. http://www.bearcat1.com/scanners.htm they are offering the BC785D w/card or BC250D w/card for S643.00 including shipping and if you send check for payment $617.00 per there website. Several months back I purchased ...

Haloncloud

About a year ago went threw same problem with Verizon. Wanted to purchase new unit for ambulance. Verizon said they don't sell mobile units anymore and don't support them. I had source for new unit but Verizon would not program for there system. About a month later we had cord on handset go bad and ...

Haloncloud

Here is a few that I have found in past but havent used personally. I think this might be what you might be looking for.

http://electronickits.com/kit/complete/elec/ck1601.htm

http://www.web-tronics.com/pcprinporrel.html

Some intresting links here:

http://www.dai.ed.ac.uk/homes/alexc/

Haloncloud

I just so happen to have several of these DTMF kits for the Maxtrac. Seem to be pretty straight forward install PM me if you are intrested in one. Purchased and never installed. Brand new in package.

Haloncloud

David

Haloncloud

Serveral times on Ebay I have seen a Maxtrac w/ Racoteck MCC Controller does anybody know what the MCC does ? I have done a search on Google and couldnt find anything.

Thanks,

Haloncloud

Haloncloud

Ok, Here is my ? Does Motorola post-date batteries ? I just received 2 batteries from radio shop with date code of 302. They look new.

Thanks

Haloncloud

It looks like there will be 6 of us from the Richmond, Va. Area coming for the first time. Does anybody have a lodging suggestion? I have been put incharge of lodging. Thanks

Haloncloud

I have a HT100 UHF, with a alternator sound in the tx audio. I have read on another board about a noise kit? Does anyone no anything about this or does anyone have a clue what it might be?

Haloncloud

Im looking for some information about MOSCAD. Any good informational sites would be a help. Programming info. They look to be on a Allen Bradley PLC format. Thanks

Search found 34 matches

MCS2000 Codeplug

Schematic for Smart RIB

Richmond, Va. Frostfest this weekend

Portable repeater project and pics

KVL U4 Chip 24C16 ?

Increasing voltage to COR on Maxtrac

AVA - What type battery ?

Found this site with Crown Vic info.

Maratrac Stripping PL

HT750 Problem

In vehicle radio charging system.

Toyota Tundra install.

GM300 and Zetron Model 38

Maxtrac w/ Racotek MCC Controller

Battery Date Code ?

HT1000 with TX audio alternator sound

Help with MOSCAD