Batboard

ve3nsv

Does anybody know of another recorder that is comparible in size and price to the TCwL-2F?

ve3nsv

I'm in the same boat and have only been able to get them to answer the phone once in the last 8 weeks.

ve3nsv

What model gateways did you get? If they're TRBO Gateways you'll need a radio connected to the gateway in order for the resource to go green and not error out on the console.

You should be able to fire up the PC, make sure the DCPM is running with no errors and then launch the MIP application.

ve3nsv

Commercial series Global Tuner should do the trick. It's the same cable to align that it is to read. You only need the adapter to upgrade the firmware.

ve3nsv

From the help pane. Primary ID (Hex) This is the ID used to identify Motorola Data Communication (MDC) messages transmitted to a radio. It is sent out to the target radio during Call Alert or emergency. A user may enter up to a maximum of 4 hexadecimal digits in the text box. Range Maximum DEEE Mini...

ve3nsv

You should be able to do a recovery also in the CPS which will firmware update and load a generic codeplug in it.

ve3nsv

1225 CPS V4 runs fine on Windows XP.

ve3nsv

Does it have the panoramic moon roof in it? If so, there is zero roof area for antennas.

I own a 2018 Ford Edge Sport.

ve3nsv

XPR-8400 Pinout

Pin 21 - COR - Program for COR/PL/ TG Detect
Pin 17 - PTT - Program for PTT
Pin 14 - RX Audio
pin 12 - Audio GND
Pin 11 - TX audio

ve3nsv

I would take the +5 and input that into an npn transistor with a 1k resistor. That will give you an active low signal that you can feed into the CDM.

ve3nsv

Are you sure about your Capacity Plus programming? Does it work when you are local to the repeater? I've had some issues with the SLR5700 in Capacity Plus with older XPR6350's not accessing or passing audio. I even opened a case with Motorola which went nowhere. It was just one department with 5 rad...

ve3nsv

Remove busy channel lockout or channel free in TRBO gear and all your problems will be solved.

As mentioned before you are likely hearing the local TX oscillator.

ve3nsv

Have you tried injecting the audio on pin 5?

ve3nsv

Just fired up an archive CP200XLS codeplug and I only show DTMF encode.

ve3nsv

I have a Trident Marauder manual. Not sure what the difference is between the Raider and Marauder?

ve3nsv

Under Edit / Preferences / check "Clone Radio Identity". You need to edit the CPS options (either from File or Edit? Going from memory, as many time as I've used the software, I should know better!) to actually clone the ID and not simply ignore what's entered into the text box (thus leavi...

ve3nsv

I just booted to DOS yesterday on my Dell M4700 via a USB thumb drive and programmed some HT-1000's so you should have any issues.

ve3nsv

I can't program the commercial series radios with my Sealevel USB to serial adapter and have to use a my dock with the serial port.

ve3nsv

I find the delay on the TRBO vocoder is usually sufficient enough when going from analog to TRBO. I would just go radio to radio and give it a try.

PTT to COR
COR to PTT
TX to RCV
RCV to TX
GND to GND

ve3nsv

Yes that would be correct.

ve3nsv

The repeater didn't TX unless you were siting in front of it and disagree? You transmitted on the output of the repeater, that's why the receive radio received your text message.

ve3nsv

You sent the text message directly to the radio and bypassed the repeater.

ve3nsv

Are you sure you went through the repeater and not directly to the other radio?

Programmed the digital frequency with the RX freq that's in our radios

ve3nsv

Yes you'll need a control station unless you're using a console that does direct integration to a TRBO system like Avtec and a few other vendors do.

ve3nsv

I think any local or tone remote solution should work fine. All accessory pin programming will have to be done through the option board. I don't think you can do COR on receive in Conn + so you'll have to do vox on receive.

ve3nsv

There was a period of time where disabling / enabling the radio in device manager worked for me.

ve3nsv

Yes I have tried C02, B03 & C03 and 15 MRTI Rx Carrier* O.C. Goes to ground with properly coded carrier.

ve3nsv

Firmware is 3.02.003 and rx activation is programmed for carrier & PL.

ve3nsv

Has anybody seen this issue where any COR line on the MTR2000 goes active when the PTT line is used? I've tried PTT and COR off the J5 and J7 connector with the same results. The station is programmed as a base station.

ve3nsv

Any chance it was inhibited via MDC?

ve3nsv

I have used a NCS-C150 Two Radio Interop Switch from collcomm inc to link a P25 phase II digital to conventional analog with good success. Just thought I'd add to this thread in case it comes up in a search for somebody looking for a similar solution. http://www.collcomminc.com/interoperability-swit...

ve3nsv

Hi Jim,

I unhooked the radio interface at the Firecom intercom gateway. I haven't gotten into any deep troubleshooting as of yet. I was just looking to see if anybody else had seen this issue as it's a fairly common setup.

ve3nsv

Unhooking the Firecom radio interface / intercom yielded the same results.

ve3nsv

I have a customer that has an issue were the XTL5000 (Remote Mount) PTT's when the Federal Q is used. I have narrowed it down to the radio itself as it does have a Firecom attached. I fixed it a few years ago with an inline power filter on the radio but it seem to be acting up again. One of the loca...

ve3nsv

This is the information I was given during training so I'd say yes.

ve3nsv

You could always go this route.

http://www.wirelesscorpltd.com/solution ... ific/x10dr

ve3nsv

Hello,

Has anybody had any success getting an off-hook contact closure from a Cisco CP-9971 phone for the MCC5500 call director?

ve3nsv

I just fired up V4 1225 and opened a GR1225 codeplug and it won't take 325N or the inverted equivalent 526.

ve3nsv

Is what's showing in your "channel position" tab lining up with what's programmed into the "conventional personalities" tab?

ve3nsv

A simple R.I.C.K. controller will give you vox.

ve3nsv

Jumping pins 7 & 9 together works also if you aren't using emerg.

ve3nsv

You can use Unicast if you just need two devices to talk to each other over a network. If you need multiple consoles / desk sets to talk to each other then Multicast is likely your only choice.

ve3nsv

The IP-224 will work for you. Put the VHF radio on port 1 configured for local mode and the low band on port 2 configured for tone mode. Then just patch the two ports together on the web interface and you're off to the races.

ve3nsv

Are you using emerg? If not you could jumper pin 7 & 9 together and just switch the main line to switched ignition power. This will turn the radio on whenever power is applied to the radio power connector. I know this solution isn't ideal but will keep this radio in service until they decided to...

ve3nsv

Under accessories, disable repeat path check box. Check it and write the repeater.

Pin 17 PTT
Pin 11 Mic hi
Pin 14 RX audio
Pin 12 Audio Ground
Pin 16 & 18 Ground
Pin 8 Power Ground
Pin 7 switched B+
Pin 19 Program for CSQ or PL/Talk Group Detect

ve3nsv

I was going to mention this also but would expect a Passport capable radio to be a CDM1550LS+. I don't see any reason why you couldn't put a Passport board in a CDM1250 radio though. You should be able to read this radio and see whether it has an option board enabled in the channel personality. I ki...

ve3nsv

Make sure each radio doesn't have the same radio ID. This has bitten me before.

ve3nsv

What are you needing exactly? It's pretty much the same as a GR1225 repeater but in a metal rack mountable box.

ve3nsv

You should be fine with that configuration. Just play with the accessory mic gain on the CM200 to achieve the desired repeat deviation.

ve3nsv

What trunked system? I believe the HT1550XLS only does LTR trunking.

Search found 281 matches