Users may not create topics, posts, or private messages containing or relating to the following material (especially pertaining to Motorola copyrighted software, unless you want Motorola to come along and shut this site down):

  • Listing for sale or trade of, or links to sites offering for sale or trade of, or giving away, Radio
    Service Software (RSS) or Customer Programming Software (CPS)
  • Profanity, pornography, defamation, or slanderous remarks directed towards any individual or entity
  • Commercial advertising (except in the Batboard Vendors forum, as approved by the Admin/Mod Staff)
  • Any other items which may be deemed as offensive

If any topics, posts, or private messages containing or relating to the aforementioned material are brought to the attention of the Admin/Mod Staff, they will be deleted.

Additional FAQ items appear here in Forum Rules. Please review them for posting guidelines and further clarification.

CM-200 Programming Question

This forum is for discussions regarding all aspects of Motorola radio programming, including hardware, computers, installation and use of RSS/CPS, firmware upgrades, and troubleshooting. There are subforums for discussions of codeplugs, and also for software/firmware release notes and issues.

Moderator: Queue Moderator

User avatar
Tron
Posts: 259
Joined: Fri Sep 14, 2001 4:00 pm
What radios do you own?: Too many to list

CM-200 Programming Question

Postby Tron » Tue Oct 16, 2012 8:06 am

Trying to get a VHF CM-200 programmed for MDT operation.

Have it pretty well programmed, but have a problem, however. When keying up the radio from the accy plug, Pin 3, it will not transmit the PL tone. Front hand mic works OK. Have tried setting it from Ext mic to Data, and it makes no difference.

Other programming is as follows:

Rx audio type (Flat Audio)
Ext PTT source ( Ext mic and Flat Tx Audio )
Data PTT Audio Source ( Ext Mic and Flat Tx Audio )

Accy Package (Default )

Pin 8 PL/CSQ/TG Detect
Pin 12 Rx Audio Mute

Any thoughts on this?

Tron
"Where the Old Soo crosses the New Soo, Duplainville, Wisconsin"

Al
Posts: 1045
Joined: Tue Sep 04, 2001 4:00 pm

Re: CM-200 Programming Question

Postby Al » Thu Oct 18, 2012 6:25 pm

Accessory pins 8, 12, and 14 can be programmed for tx PL inhibit. I noticed that you're using 8 and 12. Is anything connected to 14? Is pin 14 programming OK?

User avatar
Tron
Posts: 259
Joined: Fri Sep 14, 2001 4:00 pm
What radios do you own?: Too many to list

Re: CM-200 Programming Question

Postby Tron » Thu Oct 18, 2012 7:32 pm

Nothing hooked to Pin 14 and it shows unassigned in the software.
"Where the Old Soo crosses the New Soo, Duplainville, Wisconsin"

User avatar
Tron
Posts: 259
Joined: Fri Sep 14, 2001 4:00 pm
What radios do you own?: Too many to list

Re: CM-200 Programming Question

Postby Tron » Thu Oct 18, 2012 7:34 pm

Also, Accy package = Default
"Where the Old Soo crosses the New Soo, Duplainville, Wisconsin"

User avatar
wavetar
Administrator
Posts: 7337
Joined: Sun Sep 09, 2001 4:00 pm

Re: CM-200 Programming Question

Postby wavetar » Fri Oct 19, 2012 2:35 am

Tron wrote:Ext PTT source ( Ext mic and Flat Tx Audio )
Tron


This setting is your problem. You need to choose 'Ext Mic' only for the Ext PTT source, or else the Flat Tx Audio setting takes precedence and the PL is stripped. You only want Flat for Data PTT (no PL wanted for that).
No trees were harmed in the posting of this message...however an extraordinarily large number of electrons were horribly inconvenienced.

Welcome to the /\/\achine.

User avatar
Tron
Posts: 259
Joined: Fri Sep 14, 2001 4:00 pm
What radios do you own?: Too many to list

Re: CM-200 Programming Question

Postby Tron » Sun Oct 21, 2012 7:52 pm

Thanks. I doodled around with some of the settings and am able to get PL on Tx with flat for data.

Tron
"Where the Old Soo crosses the New Soo, Duplainville, Wisconsin"

User avatar
Tron
Posts: 259
Joined: Fri Sep 14, 2001 4:00 pm
What radios do you own?: Too many to list

Re: CM-200 Programming Question

Postby Tron » Sun Oct 21, 2012 7:57 pm

What one wouldn't give for a detailed hard copy "service" manual for this stuff these days!
"Where the Old Soo crosses the New Soo, Duplainville, Wisconsin"


Return to “Radio Programming”

Who is online

Users browsing this forum: No registered users and 1 guest