Saber III with 15ch
Moderator: Queue Moderator
-
- Posts: 267
- Joined: Wed Oct 16, 2002 4:24 am
- What radios do you own?: XTS3000 III, MTS2000 III,
Saber III with 15ch
I have a Saber III normal, and it shows 12ch on the label, yet the channel selector can rotate to 15 positions. Is that extra channels? or just a malfunction? thanks.
Motoman at your service!
Re: Saber III with 15ch
It "should" go to 16 if the stop was modified.
Generic knob-pot for the saber/system saber housings/chasis.
Generic knob-pot for the saber/system saber housings/chasis.
Motoman wrote:I have a Saber III normal, and it shows 12ch on the label, yet the channel selector can rotate to 15 positions. Is that extra channels? or just a malfunction? thanks.

-
- Batboard $upporter
- Posts: 2884
- Joined: Mon Sep 03, 2001 4:00 pm
- Tom in D.C.
- Posts: 3859
- Joined: Tue Sep 04, 2001 4:00 pm
- What radios do you own?: Progreso soup can with CRT
Saber switch...
There is a small stop-ring which on your radio is out of position, or it may be missing. It should have the underside, single tab, on the indentation at the channel 9 position. Reset the ring to that position and the knob will stop at 12 as it should.
Tom in D.C.
In 1920, the U.S. Post Office Department ruled
that children may not be sent by parcel post.
In 1920, the U.S. Post Office Department ruled
that children may not be sent by parcel post.
Would this work with a Saber 1?10-95 wrote:You can actually hex edit channels 13-16 into the radios codeplug and it will then read and write with those channels in the radio but if you ever delete the channels from the codeplug you'll have to re-hex them in. I did this once to see if it would actually work and it did.
Frank
Yes, I have done it with a Saber 1.IslesFan wrote:Would this work with a Saber 1?10-95 wrote:You can actually hex edit channels 13-16 into the radios codeplug and it will then read and write with those channels in the radio but if you ever delete the channels from the codeplug you'll have to re-hex them in. I did this once to see if it would actually work and it did.
Frank
Frank
When you add these channels via hex edit, are they viewable/editable in the saber RSS?10-95 wrote:Yes, I have done it with a Saber 1.IslesFan wrote:Would this work with a Saber 1?10-95 wrote:You can actually hex edit channels 13-16 into the radios codeplug and it will then read and write with those channels in the radio but if you ever delete the channels from the codeplug you'll have to re-hex them in. I did this once to see if it would actually work and it did.
Frank
Frank
Yes they are, but you can never delete them or you'll have to go back and hex edit them back in . You can edit the information in the new channels in the RSS just don't delete the channel positions.IslesFan wrote:When you add these channels via hex edit, are they viewable/editable in the saber RSS?10-95 wrote:Yes, I have done it with a Saber 1.IslesFan wrote: Would this work with a Saber 1?
Frank
Frank
Frank,10-95 wrote:Yes they are, but you can never delete them or you'll have to go back and hex edit them back in . You can edit the information in the new channels in the RSS just don't delete the channel positions.IslesFan wrote:When you add these channels via hex edit, are they viewable/editable in the saber RSS?10-95 wrote: Yes, I have done it with a Saber 1.
Frank
Frank
Do you know how to make the channel knob go to 16 channels?
--IslesFan
- Tom in D.C.
- Posts: 3859
- Joined: Tue Sep 04, 2001 4:00 pm
- What radios do you own?: Progreso soup can with CRT
Saber switch...
AS NOTED ABOVE, there is a stop ring under the selector knob.
Remove the ring and you will go to 16 positions.
Remove the ring and you will go to 16 positions.
Tom in D.C.
In 1920, the U.S. Post Office Department ruled
that children may not be sent by parcel post.
In 1920, the U.S. Post Office Department ruled
that children may not be sent by parcel post.
16 channel positions.
Hello.
To do all positions, remove the stop.
To make it a bit clear.
One you have hex edited the channels on, you do not want to DELETE them.
You can edit the extra channels all you want, just do not blank out the channels.
write in any valid frequency(s) you choose before you write to the codeplug.
To do all positions, remove the stop.
To make it a bit clear.
One you have hex edited the channels on, you do not want to DELETE them.
You can edit the extra channels all you want, just do not blank out the channels.
write in any valid frequency(s) you choose before you write to the codeplug.
Re: Saber switch...
I understand that. Whats the best way to remove the ring?Tom in D.C. wrote:AS NOTED ABOVE, there is a stop ring under the selector knob.
Remove the ring and you will go to 16 positions.
- Tom in D.C.
- Posts: 3859
- Joined: Tue Sep 04, 2001 4:00 pm
- What radios do you own?: Progreso soup can with CRT
S3 switch setup
The ring just sits in place. If you first remove the outer knob, then remove the adapter (plastic) underneath, the ring will be accessible and adjustable. When I said above that you put the tab into position 9 I was relying on my memory, so you may have to cut and try to get the ring set so that the knob stops on 12, if that's what you're trying to do.
Tom in D.C.
In 1920, the U.S. Post Office Department ruled
that children may not be sent by parcel post.
In 1920, the U.S. Post Office Department ruled
that children may not be sent by parcel post.
I removed the ring, edited the codeplug for 15 channels(my radio wont go to the 16th channel) and then I tried to upload the new codeplug with 15 legit channels in to the radio. It uploads the firmware sucessfully, but when I go to channel positions 13-15, the radio shows(i've checked with the radio alignment screens) that its on channel 12, yet if i I load my saved codeplug with 15 channels, it'll show I'm on 13-15 correctly, but the channel isnt working.
This is a saber 1, H43SAN7139CN, unless I'm missing something?
Edit: If I go to view radio information, For Number of Channels, it has: 15 / 12, Which I think means 15 channels out of a max of 12, Maybe I need to do some more hex editing?
This is a saber 1, H43SAN7139CN, unless I'm missing something?
Edit: If I go to view radio information, For Number of Channels, it has: 15 / 12, Which I think means 15 channels out of a max of 12, Maybe I need to do some more hex editing?
IslesFan wrote:Heh, it works!
I think I just need to do a channel align(Which I have NO idea how to do), because it appeared that for channels 1-12 the RSS set it automatically.
Thanks to 10-95 and Tom in DC.
Congradulations, glad you got it working! I neverf had that problem on any I evere did, at least you got it now.
Frank
Yeah, just need to align those three channels, because apparently, the saber RSS sets the settings automacially for the first 12 channels, but not for 13-15, so I have no idea how to align those three channels. Thats why I didn't think it worked, because I set one of the channels as a weather channel, and wasn't coming in.10-95 wrote:IslesFan wrote:Heh, it works!
I think I just need to do a channel align(Which I have NO idea how to do), because it appeared that for channels 1-12 the RSS set it automatically.
Thanks to 10-95 and Tom in DC.
Congradulations, glad you got it working! I neverf had that problem on any I evere did, at least you got it now.
Frank
So now I have two issues with my saber:
1. Need to align those three channels
2. Low Battery Warning isn't kicking in, so I don't know if its the battery, or the setting in the RSS is wrong.
--IslesFan
- petrus
- Posts: 40
- Joined: Wed Feb 05, 2003 12:16 am
- What radios do you own?: never goin out without a radio
IslesFan, You're right.
The radio can' t get the alignment for the aditinonal 3 chanels.
The file tell the radio to align only 12 chanels. So You have to
change the file again.
If You use a hex editor to do this, please take a look at 0000F80.
You will find in the ascii text box "C".
"C" stands for 12 chanels, D for 13, E for 14, F for 15.
Instead of "C" You have to use "F" for 15 chanels. If the file is ok,
the radio will do the alignment for 15 chanels.
I tested it two days ago with two radios and 14 chanels. Hope it
works for You too.
Best greetings
andreas
If You'll send me Your eMail adress, I could send you an aditional screen shoot.
The radio can' t get the alignment for the aditinonal 3 chanels.
The file tell the radio to align only 12 chanels. So You have to
change the file again.
If You use a hex editor to do this, please take a look at 0000F80.
You will find in the ascii text box "C".
"C" stands for 12 chanels, D for 13, E for 14, F for 15.
Instead of "C" You have to use "F" for 15 chanels. If the file is ok,
the radio will do the alignment for 15 chanels.
I tested it two days ago with two radios and 14 chanels. Hope it
works for You too.
Best greetings
andreas
If You'll send me Your eMail adress, I could send you an aditional screen shoot.