gp300 programming problem

turbozeke418 · Post by **turbozeke418** » Sun Jun 11, 2006 4:02 am

I have the software for most motorola radios. I have uploaded the program for the GP300 and run it in DOS mode like it should be. The program starts up fine and the radio beeps when you do a com check and says successful. When I try to read the radio or do anything else with it...it says that the software doesn't support it and I need to insert disc 2?? Anyone have this problem or know a way around it so that I can can program this radio?
thanks!!!

Post by **wavetar** » Sun Jun 11, 2006 6:17 am

It sounds like you are running an older version of the GP300 RSS, and it doesn't recognize your radio model. SInce it can't find it in it's own .mdf file, it is asking for disk #2, as that's where the .mdf file data resides for set-up. What version are yuo running?

Todd

MITYTONE · Post by **MITYTONE** » Thu Jun 15, 2006 11:35 pm

The experience i've had is that that when you're asked for disk #2, you have to insert the same disk the press enter for the entire software to be installed..I think this is due to the fact that The old version was contained on 2 disks instead of one.

Post by **wavetar** » Fri Jun 16, 2006 3:20 am

MITYTONE wrote:The experience i've had is that that when you're asked for disk #2, you have to insert the same disk the press enter for the entire software to be installed..I think this is due to the fact that The old version was contained on 2 disks instead of one.

That is during install of the software...his is already installed & is asking for the disk after trying to read the radio.

Todd

Will · Post by **Will** » Tue Jun 20, 2006 4:27 pm

. "uploaded the program for the GP300 "

This runs up a BIG RED flag.

And the same symptoms for a GP88, ect, that are labled GP300 and using different versions of the GP300 RSS.

sipep888 · Post by **sipep888** » Wed Jul 12, 2006 5:22 pm

turbozeke418 wrote:I have the software for most motorola radios. I have uploaded the program for the GP300 and run it in DOS mode like it should be. The program starts up fine and the radio beeps when you do a com check and says successful. When I try to read the radio or do anything else with it...it says that the software doesn't support it and I need to insert disc 2?? Anyone have this problem or know a way around it so that I can can program this radio?
thanks!!!

I think we have same problem"insert disk"for radio definition?i hope
someone can help us run our software back to normal(this thing happen
after my hard disk got defective and when i re install the orig software
i got this sort of problem,i got the diskette but for 12yrs on storage it is
also corrupted,can't read it anymore with my diskette drive.

sipep888

HLA · Post by **HLA** » Wed Jul 12, 2006 7:13 pm

another diagnosis it that your radio has been hacked by another version of rss and your version don't recognize the number of channels it's supposed to have or it's been hacked out of band.

sipep888 · Post by **sipep888** » Sun Jul 16, 2006 6:02 am

HLA wrote:another diagnosis it that your radio has been hacked by another version of rss and your version don't recognize the number of channels it's supposed to have or it's been hacked out of band.

I dont think so sir,same thing happen with my 16 channel GM300?
(Model Definition file NOT FOUND INSERT DISK PRESS F2 to continue)

Enrique Torres · Post by **Enrique Torres** » Fri Jul 28, 2006 12:29 pm

[I don't get the point of your post. If you'd like to offer up some advice or other constructive discussion to this thread - go for it. Posting the same cryptic post will simply result in us turning off your account.

-Alex]

gp300 programming problem

gp300 programming problem

Re: gp300 programming problem