Need help with the 26 pin rear Accessory connector on PM 1500. I cant seem to find a COR.
Heres the model 19 connector pinout:
Pin 1 - 12v+ DC
Pin 2 - DC Gnd
Pin 3 - Discriminator Audio
Pin 4 - Shield Gnd
Pin 5 - Mic Audio
Pin 6 - Busy
Pin 7 - Mic PTT
Pin 8 - Decode/PL detect
Pin 9 - COR/CSQ Detect
Pin 10 - Ack/Flat TX Audio
Any help matching these to the correct pin on the PM 1500 is greatly appreciated.
Connecting Zetron model 19 to PM 1500
Moderator: Queue Moderator
Connecting Zetron model 19 to PM 1500
If Stupidity got us into this mess, then why cant it get us out?
Re: Connecting Zetron model 19 to PM 1500
I haven't seen a PM1500 yet, but if it's the same 26-pin accessory connector as the XTL series, then pin 13 should be "Chan_act"...channel activation or carrier detect. Not sure if it's programmable or not. You can see the pin out in this thread here:
http://batboard.batlabs.com/viewtopic.php?f=4&t=77498
Good luck,
Todd
http://batboard.batlabs.com/viewtopic.php?f=4&t=77498
Good luck,
Todd
No trees were harmed in the posting of this message...however an extraordinarily large number of electrons were horribly inconvenienced.
Welcome to the /\/\achine.
Welcome to the /\/\achine.
Re: Connecting Zetron model 19 to PM 1500
I guess you haven't checked your private email. I do have the pin out connections for the PM1500. The
manual I have doesn't show a 26 pin connector though. It is a DB25 pin connector along side the small
round GCAI connectors going to the control head. All the PM1500 radios I have seen are 100 watt mobiles
and as such don't have the funky 26 pin accessory connectors like the CDM radios have.
Provide me with a valid email address and I will send you the PDF file I made with the DB25 connector
info on the pin connections.
Jim
jimszal at hotmail dot com
manual I have doesn't show a 26 pin connector though. It is a DB25 pin connector along side the small
round GCAI connectors going to the control head. All the PM1500 radios I have seen are 100 watt mobiles
and as such don't have the funky 26 pin accessory connectors like the CDM radios have.
Provide me with a valid email address and I will send you the PDF file I made with the DB25 connector
info on the pin connections.
Jim
jimszal at hotmail dot com
clmassey wrote:Need help with the 26 pin rear Accessory connector on PM 1500. I cant seem to find a COR.
Heres the model 19 connector pinout:
Pin 1 - 12v+ DC
Pin 2 - DC Gnd
Pin 3 - Discriminator Audio
Pin 4 - Shield Gnd
Pin 5 - Mic Audio
Pin 6 - Busy
Pin 7 - Mic PTT
Pin 8 - Decode/PL detect
Pin 9 - COR/CSQ Detect
Pin 10 - Ack/Flat TX Audio
Any help matching these to the correct pin on the PM 1500 is greatly appreciated.
Re: Connecting Zetron model 19 to PM 1500
I must have been asleep when I typed CDM radio. I meant to say the XTL mobiles.
Jim
Jim
[/quote]clmassey wrote:Need help with the 26 pin rear Accessory connector on PM 1500. I cant seem to find a COR.
Heres the model 19 connector pinout:
Pin 1 - 12v+ DC
Pin 2 - DC Gnd
Pin 3 - Discriminator Audio
Pin 4 - Shield Gnd
Pin 5 - Mic Audio
Pin 6 - Busy
Pin 7 - Mic PTT
Pin 8 - Decode/PL detect
Pin 9 - COR/CSQ Detect
Pin 10 - Ack/Flat TX Audio
Any help matching these to the correct pin on the PM 1500 is greatly appreciated.