OT: Fujitsu Ten radios

The General forum is where users can discuss any topic regarding Motorola communications equipment - hardware, software, etc. There are also several focused forums on this board, so please take the time to ensure that your questions doesn't fall into one of those categories before posting here!

Moderator: Queue Moderator

Post Reply
User avatar
HumHead
Moderator
Posts: 1769
Joined: Tue Sep 25, 2001 4:00 pm

OT: Fujitsu Ten radios

Post by HumHead »

I went off today in serach of a problem with a cross-band link for one of my ambulance corps (the VHF side was stuck in CSQ)

The previous radio person (long since gone) had a thing for using the cheapest radio available, so I've been getting rid of a lot of Maxon, Midland, etc. I was afraid of what I would find at the site, and was initially rather relieved when I found a Motorola cabinet that my 2135 key opened without a problem. That's where the happiness ended.

Inside the cabinet were two Fujitsu Ten mobiles, one VHF and one UHF, with a shop-built controller, and a power supply (no mics, documents, etc.). The whole thing was apparently put together in 1989 by a now defunct shop.

Luckily, fixing the problem was as simple taking the VHF mobile off of monitor mode.

Does anyone have any information, or sources for information on Fujitsu Ten radios? These were the first I'd ever seen. The models were: FTM40-3092H (UHF) and FTM15-3092L (VHF). I'd love to find any information, manuals, and programming requirements (not that these will be hanging around if they develop problems).

The site itself made for an interesting visit. The site is located in the attic of a 100 year old chapel on top of a mountain. Since access is a bit of a climb, new equipment goes in, but old stuff doesn't come out. At the far end of the attic was an amazing collection of old GE, military, and ham gear, as well as a couple of gutted Twin Vs.

In addition to our cross-band link, there is a similar station for one of our FDs, and several remote bases for the county Bureau of Emergency Services. The AC wiring is scary (old wiring and screw -in fuses), and the back-up power is not existant. The only grounding in the place was on our station, and that consisted of a piece of 1/2" braid, connected with a Stak-On to a cabinet screw, running to an aligator clip clamped to a radiator. Not a Poly-Phaser in sight. :roll:

And- this is one of the primary public safety sites, with the installs done by "professionals" Time to make some noise... :evil:
User avatar
wa2zdy
Posts: 1744
Joined: Mon Jul 01, 2002 9:13 am

Post by wa2zdy »

One word for what you described: Ouch.

(that's in place of the TWO word phrase I would normally use that the first half would be right in place in a chapel . . .holy . . .. !)

Good luck,
Chris,
Hamming 31 years
http://www.wa2zdy.com
Wesley Chapel, Pasco County, Florida
Snow? What's that?!
The human race is proof that Darwin was wrong.
User avatar
CyberSlicer
Batboard $upporter
Posts: 86
Joined: Tue Sep 04, 2001 4:00 pm

Fujitsu Ten radios

Post by CyberSlicer »

The FTM40-3092H (UHF) was a fairly popular radio about ten years or so ago due to it's ability to have the eeprom programmed so that a switch could be added to the radio chassis to program it "on the fly" so to speak via the keypad. A lot of two-way shops used them as they were so easy to program in customer's frequencies and PL tones for testing from the service van. I still have one. They're a good sounding and trouble free radio for the most part. I've had mine since '91 and never had a problem with it.

Have a Merry Christmas everyone.

Don
User avatar
Monty
Administrator
Posts: 2613
Joined: Tue Sep 04, 2001 4:00 pm

Post by Monty »

Does anyone have any information, or sources for information on Fujitsu Ten radios? These were the first I'd ever seen. The models were: FTM40-3092H (UHF) and FTM15-3092L (VHF). I'd love to find any information, manuals, and programming requirements (not that these will be hanging around if they develop problems).
I have all the Fujitsu stuff if you can't find it else where.

Some use Porgram proms, some were field programmable
with a switch.

All were a PAin to program..

Enail me direct if interested ( Perhaps after the 1st ) as that
we are not making anymore trips to the warehouse until
after new Years

MS
User avatar
rmi2065
Batboard $upporter
Posts: 69
Joined: Thu Jan 03, 2002 4:00 pm

Re: OT: Fujitsu Ten radios

Post by rmi2065 »

I'm working on a fujitsu FTM15-3092L and trying to align it. I have a few spec sheets, however, none of which have voltage info. If anyone has or knows this info and would care to share it would be a hugh help.

TIA,
Justin
Justin
Jason
Posts: 802
Joined: Mon Oct 08, 2001 4:00 pm

Re: OT: Fujitsu Ten radios

Post by Jason »

:o
Post Reply

Return to “General Motorola Solutions & Legacy Radio Discussion”