does anybody know how to change a 2 ch p110 radio to a 16 ch radio? i have the tk software but it says i need a math key for the lpt port somebody told me that you could put a jumper from pins 7 and 13 of the printer port and make it work, i tryed but it don't do you need a slow computer
thanks jeffrey
[email protected]
Re: Motorola P110 Radio Programming Questions.
Moderator: Queue Moderator
Hi:
From some of my web notes ( and I a not able to gurantee the info ) you need to make
a dongle with a wire from Pin 6 to 11, and
this is attached to the Printer Port of your
computer.
Again, I am not able to say for sure, but
that is what I have seen posted.
Also, your radio will have to be one
made piror to 1994, or have at least
more than 2 channels to be able to convert
a P110 to more than 16 channels. I beleive
you have to change the entire radio personality to a GP300...If someone has
already made this mod, they may comment
on the info.
If your radio was made after 1994, Motorola
made the Firmware to be able to support "Only" 2 channels. If you have access
to SMC soldering equipment, one can change the IC to make it work, but its trully a hassle.
I did one just to see how tough of as job it
was.....
Monty
<font size=-1>[ This Message was edited by: [email protected] on 2001-12-15 00:48 ]</font>
From some of my web notes ( and I a not able to gurantee the info ) you need to make
a dongle with a wire from Pin 6 to 11, and
this is attached to the Printer Port of your
computer.
Again, I am not able to say for sure, but
that is what I have seen posted.
Also, your radio will have to be one
made piror to 1994, or have at least
more than 2 channels to be able to convert
a P110 to more than 16 channels. I beleive
you have to change the entire radio personality to a GP300...If someone has
already made this mod, they may comment
on the info.
If your radio was made after 1994, Motorola
made the Firmware to be able to support "Only" 2 channels. If you have access
to SMC soldering equipment, one can change the IC to make it work, but its trully a hassle.
I did one just to see how tough of as job it
was.....
Monty
<font size=-1>[ This Message was edited by: [email protected] on 2001-12-15 00:48 ]</font>
TK works, I have only done one P110. Try this link http://www.batlabs.com/tk.html for info on the Math Device/Dongle. I have done several GP300's with only one problem child. I have one GP300 I can't convert no matter what I try. Otherwise I'd give TK a try, it makes things quite easier.
-
J_L_COHEN
- Posts: 121
- Joined: Thu Dec 13, 2001 4:00 pm
- What radios do you own?: Xtl5000 apx7000 Cdm1550,Ht1250
THANKS GUYS FOR THE INFO
YES TK WORKS, AND THE PINOUT IS 6 AND 11 BUT MY RADIO WAS MADE ON 9-23-95 SO WHEN I TRY TO PROG IT, IT WILL ACT LIKE A GP300, HAVE 16 CH BUT ONLY 2 WILL PROGRAM SO THE FIRM WARE MUST BE A FACTOR IN MINE, MONTY YOU SAID THAT YOU CHANGED A IC DO YOU HAVE ANY MORE INFO, HOW DID YOURS TURN OUT?
JEFFREY
YES TK WORKS, AND THE PINOUT IS 6 AND 11 BUT MY RADIO WAS MADE ON 9-23-95 SO WHEN I TRY TO PROG IT, IT WILL ACT LIKE A GP300, HAVE 16 CH BUT ONLY 2 WILL PROGRAM SO THE FIRM WARE MUST BE A FACTOR IN MINE, MONTY YOU SAID THAT YOU CHANGED A IC DO YOU HAVE ANY MORE INFO, HOW DID YOURS TURN OUT?
JEFFREY