take a look at the manual here
http://batboard.batlabs.com/viewtopic.php?f=10&t=110664

You are going to need to tune the preselector for your frequency as it is probay making your receiver def if it has not been returned to your new frequency. You mention that you have been able to program it down ...

I have had some luck getting a 151-159 split to receive in the ham band. I guess some rf boards will go further out than others. Check out this video on you tube I haven't had a lot of luck with this method. But I have only tried it to get a 450 split minitor into the 70cm ham band. It may be worth ...

There is also the case that they are LS that someone tried to turn into conventionals and blew out the tuning data. usually messing with the tuning is not the first approach to a problem like this. Hopefully you have backups of the original tuning. Could you share with us your code plug? and tell us ...

Maybe this will help it is a general setting. Let us know if this helps.

when the setting is enabled the radio will be monitoring the channel in CSQ when the mic is not hung up. try grounding the clip on the back of the mic and see if your problem goes away. I will also see if I can find were in the cps the setting is. let me know what you find out

Rich,

Can you tell us a little more about your problem? by ignore do you mean it does not unmute? or does it unmute for everything? perhaps it is monitor when mic off hook setting?

could you post the model number of your radio?

I have a quantar station that has been confirmed to have a dead SCM. The damaged module has part number TTN4094C28, and a module I was able to borrow for testing that worked in the station had part number CLN1293A.

what is the best way to determine part compatibility for the scm. I am looking at ...

Hello all, I have a Minitor iii I am trying to take slightly out of band, I can not change the split with the engineering mode because because its a two frequency pager, one of the frequencies i need is in the band the other is slightly out.

It is a 151-158.9999

the two frequencies I need are 151 ...

If I swap out the SCM do I need to realign the station? where is the alignment stored? Thanks!

Thank you everyone for your input! I will reseat all the modules tomorrow. I definitely see where there could be issues interfacing with the external controller, however I am stumped why there is no audio when repeating internally. Is there something I can check with audio routing? how about ...

I have a UHF R2 qunatar in ham service. It has a controller connected to it but the station is configured as a repeater so that P25 is passed through it. The controller is connected to the aux tx and aux rx audio on the 25 pair punch down block. The wireline is then set as a higher ptt poriority so ...

this topic has been discussed before take a look.

http://batboard.batlabs.com/viewtopic.p ... rd#p364204

You can use the unofficial Waris labtool to blow in an HT1250 codeplug, but if you do I believe the radio will need to be retuned.

you can also use global tuner to save the tuning data before blowing in a new code plug. Its a pretty good rule of thumb to back up the tuning data before you do ...

Thanks for the info. I ended up getting the radio swapped out by the person I bought it from.

Thanks!

Thanks for the quick reply! Unfortunately it doesn't look like Multiplier makes batteries for the "EX" professional radios.

I have an EX500 that came with an after market battery, it seems to be the source of intermittent power to the radio. It also doesn't charge correctly. On a rapid rate charger it flashes red as the charging cycle finishes. I want to replace it but it seems the OEM batteries for these radios are ...

I have never done this with a spectra, but I have done it with a CDM. it is very simple to interface to the computer. The tx and rx audio can go to the sound card and the serial port can be used for keying and detecting a received signal. I also know repeater builder.com has good descriptions of ...

I found a you tube video that shows the replacement of a PA. it may be useful for others.

http://www.youtube.com/watch?v=m4s3lhz6 ... ature=plcp

This user also has several other videos showing repair of waris series components

I got a R split HT1250 that appears to have a dead PA. I put it on a service monitor and it only made a few hundred mW. I checked the power setting and tuning but all seems well. I am thinking about swapping out the PA myself I have a donor ht750 with the same split. Is there any reason not to just ...

Thanks for the correction, not sure how I messed that one up.

What frequencies are you trying to put into the radio? typically more than 10 mHz out of band won't happen. sounds like you are really in need of the "Q" split version which will do 403-470

I am trying to realign a used HT750 I purchased. I have realigned CDMs before and have access to all of the necessary equipment. When I go to align the PA bias I don't know what voltage set point to use. I have looked at the detailed and basic service manuals and the tuner help file. The ...

Thanks! My problem was that I had not changed directories into the directory with the files. Even though I was able to run srec2bin I was not able to generate an out put file. I am still missing the algorithm to calculate the band limits since the links to the original directions are broken. Thanks!

I am having trouble with step 4. links to the original directions are down. How do I "run srec2bin on my code plug file. when I click srec2bin in win xp a command prompt window pops up and then disappears. help would be most appreciated

Thank you Forts,
I may have to break down and buy the cable. Did you happen to notice if there are any other pins on the radio side of the cable?

Has anyone had success building a cable for the portable Trbo radios? I have tried the simple usb cable posted above with out success. Can someone with a cable take a closer look? does it have all 12 of the pins populated? looking at some fuzzy pictures online some of them appear to only have the ...

I think I figured out the problem it looks like Simulcast Operation was enabled and it does not have GPS

Thanks!!

Maybe I missed something but I don't think you can create a new code plug from nothing. I tried an old version of the code plug from this machine with out much success. Probably still worth finding a code plug to try

I have a R2 UHF Quantar running R14.09.01 that will not Tx while receiving or from the wire line. I can key the station from RSS. The station is programed to TX and RX with a Pl. when not transmitting the idle exciter will open my HT which I would not expect since PL should not be present. It did ...

First off I am assuming that this is actually astro repeater? Do you have your astro signal being injected into the receiver?

Yes. This repeater is Astro capable. I am only injecting a carrier signal into the receiver and I would like to know the signal strength. Basically I am trying to roughly ...

I am trying to look at RSSI with RSS version R14.09.01. Under service >test and measurement screen> ASTRO BER&RSSI Report, I click start RSSI Measurement, however I get a dialog box with error "Unable To Start RSSI Measurement." I am not sure why this wont work. does any one have experience with a ...

I just got a UHF R2 110watt Quantar. We are co-ordinated for 100W, we heard that when these PAs are run near full output they can be prone to failure. Does anyone have any experience with this? Should we run at 100w output?