Anybody know the part number for the mic connector pcb board. The one in the batlabs section is only the base plate not the pcb.
Thanks
Warren
HT 1000 Connector
Moderator: Queue Moderator
HI:
If you are looking to build a Program
Cable, you would be better off getting
a Connector Off of a Good Mic that has
all the Pins in good order.
A problem with the Jedi/MTX/HT1000 Series
Mic plug is the Pins get bent all the time
and if you should have a poor Cable and a
intermittent Contact during the write process
you will end up with a dead radio.
Anyhow, the Board ass'y with Pins is a
0180302E30
Or I can sell you a complete plug if you desire....But you must be able in handling
small wiring.
And with Motorola's New Policys, you may not
be able to purchase it as a seperate part for
much longer.
So Buy Now if its still availible, as Motorola is leaning more and more to
supplying only completed assemblies.
There f'in policies, not mine
Monty
If you are looking to build a Program
Cable, you would be better off getting
a Connector Off of a Good Mic that has
all the Pins in good order.
A problem with the Jedi/MTX/HT1000 Series
Mic plug is the Pins get bent all the time
and if you should have a poor Cable and a
intermittent Contact during the write process
you will end up with a dead radio.
Anyhow, the Board ass'y with Pins is a
0180302E30
Or I can sell you a complete plug if you desire....But you must be able in handling
small wiring.
And with Motorola's New Policys, you may not
be able to purchase it as a seperate part for
much longer.
So Buy Now if its still availible, as Motorola is leaning more and more to
supplying only completed assemblies.
There f'in policies, not mine
Monty
Last edited by Nand on Sun Jan 18, 2004 10:26 am, edited 1 time in total.
Hi:
Sure would like to know the
part number of the Mic you
have.
In all my cases, I have found you
are able to use a Mic Connector off
of a Old Cord ( Providing the Pins ) are
not damaged.
There are a couple of positions not used
which is Postion 12, 11,and 10 are missing, but are not use. There is NO Holes for them
but there is Holes for #13 and # 9, # 8 is already in place
All you really have to do is " relocate"
the from Positon 1 and Position 3, and relocate them to Position 13, and position 9
Sometimes, depending on the Board you need
to add a few Jumpers.
If you desire, I make Premium Clones with
Super Cable supports at both ends, Most of
mine have a External Speaker jack for Audio
measurments. They are fully tested and warranteed...These are well built cables, not
patched together with rubber bands, and glue.
If interested, I casn send a photo, or for
75.00+8.00 S & H I can send a complete cable
to you
Monty
Sure would like to know the
part number of the Mic you
have.
In all my cases, I have found you
are able to use a Mic Connector off
of a Old Cord ( Providing the Pins ) are
not damaged.
There are a couple of positions not used
which is Postion 12, 11,and 10 are missing, but are not use. There is NO Holes for them
but there is Holes for #13 and # 9, # 8 is already in place
All you really have to do is " relocate"
the from Positon 1 and Position 3, and relocate them to Position 13, and position 9
Sometimes, depending on the Board you need
to add a few Jumpers.
If you desire, I make Premium Clones with
Super Cable supports at both ends, Most of
mine have a External Speaker jack for Audio
measurments. They are fully tested and warranteed...These are well built cables, not
patched together with rubber bands, and glue.
If interested, I casn send a photo, or for
75.00+8.00 S & H I can send a complete cable
to you
Monty