in my job we are using at least 40 radios ( CM300 & few GM300), I want to configure at least two of those radios to show a PTT ID for each radio.
please advice me about the MDC decode, and how to use it
thanks a lot ...
how to configure MDC decode CM300 ????
Moderator: Queue Moderator
- firefighter13669
- New User
- Posts: 110
- Joined: Sun Jun 24, 2007 8:09 am
- What radios do you own?: M1225,F3161,F70,F5061,F33,F50V
Re: how to configure MDC decode CM300 ????
Enable MDC select the channels you want to send it on and do the same with the other .if you have the software you should be able to get it once you see mdc
KC2VHB
- HLA
- Posts: 2334
- Joined: Mon Jul 11, 2005 8:15 pm
- What radios do you own?: HT1550's, X9000's, CDM1550's
Re: how to configure MDC decode CM300 ????
bring up a personality on the screen and in the recieve side most of the way down there is a box that says signaling system, set it to mdc and you are in business.
HLA
I never check PM's so don't bother, just email me.
I won't reply to a hotmail, gmail, aol or any other generic free address, if you want me to reply use a real address.
STOP ASKING ME FOR SOFTWARE OR FIRMWARE, I JUST FORWARD ALL OF THE REQUESTS TO THE MODERATORS
I never check PM's so don't bother, just email me.
I won't reply to a hotmail, gmail, aol or any other generic free address, if you want me to reply use a real address.
STOP ASKING ME FOR SOFTWARE OR FIRMWARE, I JUST FORWARD ALL OF THE REQUESTS TO THE MODERATORS
how to configure MDC decode CM300 ????
thank you guys for your answers,
the fact is, as it was explained to me by the technical support of motorola, that the CM300 radio doesn't support the MDC decode option, you can program the PTT ID within the CM300 , but to display this ID only the CM340 & CM360 radios can display it, could any have further information please ????
the fact is, as it was explained to me by the technical support of motorola, that the CM300 radio doesn't support the MDC decode option, you can program the PTT ID within the CM300 , but to display this ID only the CM340 & CM360 radios can display it, could any have further information please ????
Re: how to configure MDC decode CM300 ????
-deleted-
Last edited by txshooter on Sat Feb 23, 2008 3:13 pm, edited 1 time in total.
Reason: incorrect info in orginal post
Reason: incorrect info in orginal post
Scott B.
"Never argue with seven men when you are carrying a six shooter..."
"Never argue with seven men when you are carrying a six shooter..."
- HLA
- Posts: 2334
- Joined: Mon Jul 11, 2005 8:15 pm
- What radios do you own?: HT1550's, X9000's, CDM1550's
Re: how to configure MDC decode CM300 ????
it can decode and display the mdc number but not an alias
HLA
I never check PM's so don't bother, just email me.
I won't reply to a hotmail, gmail, aol or any other generic free address, if you want me to reply use a real address.
STOP ASKING ME FOR SOFTWARE OR FIRMWARE, I JUST FORWARD ALL OF THE REQUESTS TO THE MODERATORS
I never check PM's so don't bother, just email me.
I won't reply to a hotmail, gmail, aol or any other generic free address, if you want me to reply use a real address.
STOP ASKING ME FOR SOFTWARE OR FIRMWARE, I JUST FORWARD ALL OF THE REQUESTS TO THE MODERATORS
Re: how to configure MDC decode CM300 ????
Make sure you go into view and choose expert view in the CPS to see all your available options. I think the receive signalling box will only show up in the channel personality in expert view.