Batboard

RonJeremy

What do I need to convert a XTL5000 W9 to a dashmount O5 radio? Do I need a special firmware version? Minimum version?

Does any O5 head will fit my unit?

Thank you

RonJeremy

Thanks! Is it really 47 CAD for the 4 ch cover?

RonJeremy

I need the part number for the plastic cover for a M1225 4 channels.

Thank you.

RonJeremy

Hi.

I ordered the 7586091B01 part number on MOL which is a CDM1550 keypad. Unfortunatly this is not the part I expected. The keypad fits but symbols on buttons are not the same as my original pad. I have arrow buttons and red X and a green check mark buttons and I would like the part number for the ...

RonJeremy

I have a XTL5000 remote mount with W9 ctrl head and I did not use it for 2 weeks. Now it shows FAIL 01/90 at power up. Nothing has been changed, cables are correctly connected.

Any idea of what the problem is?

RonJeremy

Anyone knows the exact pinout for a HMN3000A desk mic?

The board has 7 holes for wires and they have 1 to 7 number for each one.

There is no coil cord on it and I would like to put a new one to fit this mic to a CDM1250.

Any ideas?

RonJeremy

Thanks for the info

RonJeremy

Yes it's a 10 pin.

I hope finding a replacement cord, I don't want to buy a new mic $$$$.

RonJeremy

Hi.

I need the part number for the coil cord (8 wires) of a ehanced DTMF mic AARMN4026B for a CDM1250 radio.

Mine is in bad condition and I would like to buy a new replacement one.

Thank you

RonJeremy

Ok thanks!

RonJeremy

I found a Motorola speaker without housing. It's a 20W 2 ohms

Anyone knows which radio fits this spkr?

Thank you.

RonJeremy

I had time to try it.

I put electronics and flex from the 1250 head in the 1550 head housing. It works like the 1250 head. I can't get the extra 1550's buttons to work. No error.

Any bit banging way to enable buttons?

RonJeremy

Hi.

I read a few posts about swapping ctrl heads between a CDM1250 and a 1550 but I didn't find a clear answer.

I have a 1550 control head plastic housing with buttons and I was wondering If I can just swap electronics from the 1250 head and get the extra buttons working on the 1250?

I know that ...

RonJeremy

Does anyone know if Motorola sells front housing for W9 ctrl head?

If so, I would like the part #

Thanks

RonJeremy

Does anyone have the cutting chart for a Sinclair Excelsior VHF 5/8 wave antenna? .pdf or .doc would be great!

Thanks!

RonJeremy

What is the connector type on a Waris radio?

I need an adpater to connect a HT1250 to external antenna for RX only. What do I need?

Thank you

RonJeremy

Does anybody know what is the impedance of a HSN9326A mobile speaker ?

Thanks

RonJeremy

Does anyone know what is the part number for the 26 pin acc connector on rear of XTL5000 radios ?

RonJeremy

This is the way I used to do mine and it works fine :

http://www.repeater-builder.com/motorola/spectra/spectra-900mhz-vco-mod.html

You will also need a syskey for each different trunking system in your radio. This will allow you to delete everything and make more place for your ham stuff in the ...

RonJeremy

Anyone knows ?

Thanks !

RonJeremy

It's a B3 but it looks like I can program more than 10 conventional modes. If I program over 10 will it accept them ? Can I enable scan for at least 10 modes ?

RonJeremy

I have 2 modes programmed now, what is the maximum conventional modes available ?

RonJeremy

Is it possible to make a MTX838 UHF working conventional only ? I mean just like a Spectra when we remove all trunking stuff with a sys id ?

Thanks !

RonJeremy

Is there any way to extend the bandsplit on these units ?

RonJeremy

Yes. Thanks a lot !

RonJeremy

Is there any website to get the model breakdown chart for the XTL 5000 radios ?

RonJeremy

I found what I wanted. Thank you guys.

RonJeremy

What are the model numbers for 1 meg boards ? DSP is l06.03.02

RonJeremy

How can I tell if an Astro Spectra is 1 meg ? Label does not show it but the seller told me it is.

Thank you.

RonJeremy

Thank you.

RonJeremy

Hi everyone. Just wondering how to upgrade firmware on Astro Spectra mobile radios ?

RonJeremy

Ok it's a VHF 25W.

RonJeremy

Hi,

what is the part number of the CDM final transistor ?

Thank you!

RonJeremy

Any website to get that decoding chart ?

RonJeremy

Can someone tells me what is this radio ?

Model : M20URS9PW1AN

Thank you!

RonJeremy

Well it was just a cut wire on the acc plug.

Thank you Jim.

RonJeremy

What is wrong when I get two bip at power up ? Sounds like a corrupt codeplug but I don't get any error message while reading radio...

Thank you for your help !

RonJeremy

I reprogrammed an Advisor Elite on my own capcode and paging provider frequency but I get the two little antennas on the display (out of range).

I tried to reprogram many times but the pager is still disabled. I have the good capcode and freq.

Any ideas ?

Thank you!

RonJeremy

I only changed the head and hex changed from A5 to A7[/b]

RonJeremy

I did all the procedure but after fixing the fail error the radio reset goes to self check and it transmits by itself...

Anyone knows what's wrong ?

RonJeremy

Yes I have the busy led and I can not hear anything while changing mode or volume.

RonJeremy

Spectra with no RX audio. Anyone knows what it could be ?

Audio PA ?

RonJeremy

Did you get all buttons working ? Just like a real A7 ?

RonJeremy

Does anyone tried to replace a A5 head on a Spectra dash mount for A7 head like described on batlabs ?

RonJeremy

I have seen a lot of old Micor radios at a gov auction.

Just wondering if they still have some worth or it is junk

VHF, marine band 152 - 172 MHZ

I can not find a lot of info over the internet...

RonJeremy

A friend needs someone to reprogram his HT1000 or tuning it.

He lives in Southern California, Ventura County, Thousand Oaks.

I'm too far to help him.

Anyone in this area ?

Thanks a lot guys !

RonJeremy

Thank you!

RonJeremy

They are Jedi ones. NTN7143CR and NTN7144CR. Letters after these model numbers ? I have a 310 AKU2 1

it is a NTN7143CR. HLS can you figure out 1993 or 2003 ? Looks like someone is selling nos batteries but very old !

RonJeremy

I know they will not work good or not work at all if they are 10 years old. But if I purchase new batteries over an individual how could I know if they are really new or nos ?

RonJeremy

Can I figure it out on the battery label ?

Search found 122 matches