Batboard

HRN

We are trying to consolidate a bunch of Minitor V pagers and would like to swap RF boards in the like we have done with the Minitor II pagers. We have a number of 462 MHz range M5 pagers and a variety of other band RF boards we would like to put in them.

The steps I have taken:
1. Remove both RF ...

HRN

The features many of you are looking for are all available (voice and alphanumeric paging all in 1 unit) and water submersible in the Unication G1 Basic + BT and G1 GSM + BT models.

They have several promotions currently running.

PM me for more info or at www.HoffmanRadioNetwork.com.

Regards,
Jason

HRN

Gotcha, sorry about that...... I usually only submit orders, MOL repairs and check on warranty information.

HRN

Jim202 - That's interesting. I've been using Firefox for years on MOL.

Jason

HRN

Thank you ard0999 for taking the time to supply me with this info. I appreciate it, as the repeater side of things are all new to me.

HRN

Thanks for the udpate/info. I'm the Assitant EMS Coordinator at an EMS Agency. I'm an autorized radio transmitter on the low band frequency and we currently have 2 UHF repeater frequencies licensed to our EMS Agency. This would be in my response vehicle and would be used for limited, short ...

HRN

I have been kicking the idea around of setting up a vehicle repeater because of not being in a good area working and having to operate on portable radios. I was thinking I needed to get something like a Pyramid repeater like we have in our Rescue, however, as I was sitting here, I just happened to ...

HRN

Well, that was my thought. I tried some of the companies we deal with and they no longer support the old Dos radios.

HRN

My old MS-Dos laptop crashed and I replaced it with a newer laptop. The old floppy disk I had with the maratrac software on is giving me a run-time error 60. I tried to get the software off of MOL again, but saw it wasn't listed, then found this saying it is discontinued. How can I go about getting ...

HRN

The length of time for the revert n has been set too long. It can be shortened through the software.

HRN

I just found out when I called the depot the other day to send two Minitor IV pagers back for repair, that the support of them is discontinued. Anyone know the best place, both quality and price, in getting them repaired? I'm still going to be needing to send them out for repair but am not sure who ...

HRN

I did, indeed. Any way to go into a hex editor and get it back to the original? Or any other ideas? So, it sounds like, as long as I do that in a version that isn't setup for Engineering mode, I'm good to go.

HRN

I went to program a pager this evening and it appeared as I read the code plug, that it had a different serial number on the firmware vs. what was on the case. I looked at the pager on my side because the serial number on the firmware looked familiar. After thinking about it, I remember using my ...

HRN

Thanks bezking. That was kind of the conclusion I came too, but was hoping I was wrong. I had it alerting on the tones, however, just wasn't sure if it had the 'tone alert' option. Thanks.

HRN

First, let me apologize for asking this in this post, but it is a similar question about Quick Call II. The MT1000 had the switch on top to put the portable in a 'Tone Alert' mode. Can the HT1250 be put in a 'Tone Alert' mode? I have tried every setting in the menu, but can't seem to get it to limit ...

HRN

1. To my knowledge, the minitor 5 is the first pager that was capabale of having the pager run off the charger.

2. Typically, the 2 channel was just for monitoring a second frequency. However, there are different variations that can be done with that by the way the jumpers are soldered on the board ...

HRN

I know they use the same filters, but I wasn't sure about the RF Boards. If I had one I would take it apart myself, but I don't, so I thought I would throw it out for an answer. Will the RF board in an original Minitor work in a Minitor II?

Thanks.

HRN

Bump.......Surely someone has the capabilities to do this. Any help would really be appreciated. If you can't do it, but know someone who can, please let me know. Thanks.

HRN

I used to see a company that would advertise that they would add stored voice to a low band Minitor IV. I can't find the information for them and have one that needs it added. Can anyone add it to me for a reasonable price or know of any companies that will do it? The pager is already out of ...

HRN

What are the tone sets that you are looking for?

HRN

Minitor I's are also included in the trade-in plan even though they are not in the drop down list.

HRN

PM sent.

HRN

I have a bunch of used grey cases. Some are in "like new" condition.

HRN

I agree with what everyone is saying about scan. I keep my pager on scan all the time and have never had a problem. I did, however, have 1 fire company who I sold several minitor Vs to that had problems with not alerting. When I programmed their tone sets into my pager, mine tripped most of the time ...

HRN

I have been just using it with the antenna off so far, but was afraid, from what I have read, I would burn the radio up. It is only transmitting for approximate 4 seconds at a time. The only problem is, I am not exactly sure, at this point, how far the signal will go without the antenna.

HRN

Comtekk is what has gotten me thinking there is a more inexpensive way than a service monitor. I have downloaded the encoder and successfully transmitted tones and activated pagers. I just want a way to get the watts reduced and I am not sure what connectors and dummy load to get. 50 ohm is what I ...

HRN

I bought a Cushman 4000 service monitor to attempt to do this and I was able to get the tone generator to work, some of the buttons stuck, but I couldn't make it transmit. I was told by someone that I had to build something else for it to transmit, but I thought it should do it all on one unit. I ...

HRN

Is this the same adapter that connects to an external antenna? I don't have one, but I am sure I can get one somewhere if that is what I need. If you have a part number, or know how I can find one, that might help me out. I am not really familiar with these. What kind of cable would I need then to ...

HRN

My local fire company has the ability to program minitor pagers. What we would like to do is have the ability, to keep the cost down from a service monitor (which we don't need all the features) to do 2 tone encoding. We have the software on a laptop, but need to handle the radio side. We will be ...

HRN

I had several pagers with this problem. I found in looking at them that the slider switch was not in correctly. Try popping it out and putting it in the other direction. Hope that fixes your problem.

HRN

Search the forums. This has been gone over a few times on how to do it.

HRN

The original version that was released did not work with on/off duty. You have to have a later release and that is fixed.

HRN

I have run into the same problem with the standard chargers. I have also run into the problem of the amp. chargers squealing when there is no pager in the charger.

HRN

The serial number will verify to Motorola that you have the 5 year warranty. You can verify that by checking with your local dealer or calling the Motorola Depot.

HRN

Does this work on the M4 as well?

HRN

My choice is for a 60 watt radio. I am looking for a low band for my fire company. I have several 110 watt maratrac low band radios, but they only want a NEW radio. It is the philosophy of "Why would we want a 60 watt radio. We have always had 110 watt radios...." It is TRADITION.... Anyhow, I have ...

HRN

Since Motorola discontinued the maratrac and the syntor 9000, have they replaced them with any other 110 watt radios? I am trying to find a new radio that would be the equivalent. Thanks in advance.

HRN

Yeah, PPS. That is what I meant. I was just working with the MT1000 RSS when I wrote it and that was what was in my head. The "too my knowledge" part had to do with it not being available to the Minitor V.

HRN

I have been told they are 8 days. I keep my pager on scan probably 40% of the time and alert the remainder of the time (excluding weekeds, then the percentages are switched) and I get around 6 days out of it. I have had my pager since June with the original battery.

HRN

At this point, Engineer Data is not built into the RSS (To my knowledge).... That is left over from the Minitor III/IV RSS.

HRN

I have never seen the problem in the minitor V, however, I had several minitor IVs that were set to a fixed alert and that seemed to kill the volume on the pager. When the fixed alert was disabled, the volume went back to normal.

HRN

My fire company has several lapel mics for the MT1000 that must have broken wires inside. Does anyone repair these and what cost? Thanks in advance.

HRN

Embarrassingly enough, I have found out that the County, which is my neighboring county, has different Tx and Rcv frequencies. Can I say DUH! All works well now.

HRN

I did program both from scratch. I am going to try putting the second one in my vehicle and see if I can reach County then. I just find it odd both are doing the same thing (but it could be because of an atenna problem) in that ambulance, when I am pretty sure they are programmed correctly. Thanks ...

HRN

I installed a maratrac radio into an ambulance using the existing antenna the same day a newer radio was taken out to put in a newer ambulance. I programmed the radio with 18 channels and two different PLs. No one will answer when I call and I am not breaking squelch at County. I thought the first ...

HRN

I have update the firmware (v3) on several Minitor V pagers and have not noticed any difference. However, I updated the firmware on another pager and reprogrammed it directly after, taking the pager out of programming mode and entering programming mode again befroe reprogramming. I made no changes ...

HRN

A maxtrac will work for what you are looking for. What bandwidth do you need? I have one that I would consider selling and can program it for you if you would be interested.

HRN

I have successfully programmed Motorola Radius and Maxtrac radios with a PL tone and have had no problems. However, I am having a problem getting a PL tone programmed into 2 maratracs. One is a UHF and one is a low band. On the Mode screen for the channels with PL tones, I have the TX set to TPL and ...

Search found 48 matches

Minitor V RF Board Replacement

Re: MINITOR VI (YES 6)

Re: MOL URL changes tonight

Re: MOL URL changes tonight

Re: Using a CDM1250 for a repeater

Re: Using a CDM1250 for a repeater

Using a CDM1250 for a repeater

Re: software part numbers

Re: software part numbers

Re: Min V Recipition Problem

Motorola Minitor IV Repairs

Re: Minitor V Programming & Serial Numbers

Minitor V Programming & Serial Numbers

Re: HT1250 Quick Call II

Re: HT1250 Quick Call II

Re: Minitor II questions.

Minitor I RF Board

Re: Adding stored voice to a Minitor IV

Adding stored voice to a Minitor IV

Re: W.T.B. Minitor II Tone Reeds

Re: Minitor V Pager Trade-In Promo

Re: Min II Part number?

Re: Min II Part number?

Re: Minitor V-in depth professional assistance needed

Re: Reducing Transmitting Power

Re: Reducing Transmitting Power

Re: Reducing Transmitting Power

Re: Reducing Transmitting Power

Reducing Transmitting Power

Loose Battery M5

2 channel convert

That's correct

Chargers

5 year plan

110 watt mobile radios

Refurbing/Fixing MT1000 lapel mics

Maratrac Programming/transmitting issue

Motorola Maratrac PL Programming