Batboard

Ra

Looking for the Motorola OEM service monitor test whip antenna that came with the R2200 series communications service monitors. The guy with the big red tip and a BNC right angle male connector.

Thanks,

RA

Ra

Monty I miss you, you were such a great help.

Sweet Dreams Dear One.

Ra

If anyone knows the part number for the service manual for SP10's please advise.

Thanks in advance!!!

Ra

Ra

Does someone know the and size of the Torx wrench used to remove the four (4) housing screws on the XTN radio?

If anyone knows the size I sure would appreciate it.

Cheers,

Thanks in advance!

Ra

Ra

Thanks !

Ra

When I search for P50 nothing comes back, all other models bring results but not the P50 for some reason. Why? There are lots of P50 posts buy I cannot get them in search.

Ra

I have two P50's on 48mHz and the wrong antennas are on the units. Does anyone have the correct low band antenna part number?

Greatly appreciated!

PS: Is the threaded ¼-32 x 3/16" ring "hot" or should the correct antenna make contact to the jack below the ring on low band models

?

Ra

Many thanks Haydn!

I think it is the Super-Duty as it is 4wd, gasoline as it hauls 600 gallons of water in addition to all the pumps and onboard gear. It is a BIG dual rear tire engine. I will get the model in a few minutes as the vehicle is on its way over. Will the line stand a 4 amp load?

Ra

Ra

Hi all,

I am installing a radio in a volenteer fire brush truck. I am looking for the switched 12 volt line (ignition - accessory) wire color. That is, the line that is hot only when the vehicle is running or in accs position.

Does anyone know which color Ford uses these days. It is a 2003 ...

Ra

Anyone know the Motorola p/n for a 3/4" rubber hole plug??

Theu used to make one to fill removed NMO antenna holes.

Thanks in advance!!

Ra

Thank you Nand! Just what I needed to know, as usual. I like your new face!

Ra

Ra

Hay guys,

During radio case refurbs one needs to somehow glue the replacement felt to the inside of the new case. Motorola does such a nice flat factory job.

What is the appropiate glue to use that will not impede the acoustics?

What does Monty use? Will he tell?

Ra

Ra

Yes it was a nice gift! Thanks to each of you for taking the time to help me! I appreciate everything guys! Think I will send it to Monty for a bath, new outer clothes and a new internal mind!

Ra

Ra

Thanks guys, yes it is very helpful N9UPC.

The thing is the label is gone and that is the problem. It was a gift and came without the label.

Here is a pix.

Ra

<img src=http://www.southpacificgateway.com/mic/MVC-450F.JPG>

Ra

I have a AAH25RDG9AA4AN and could not match it correctly in the Batlabs charts.

Could someone tell me what it is? Has a full keypad without the display. 16 Channel. 3 buttons only above the keypad.

What is main difference between the 750 and the 1250 and which is this?

Ra

Ra

Ah, You are likely right, likely right.

All companies are crooks now. But you see I am an old old guy and in my Motorola days they did everything for us that they possibly could.

Free radios, full support - anything. Motorola supported us service guys to a perfect tee. They knew us by name even ...

Ra

We should, once again, thank Motorola for the lives saved. Radios underground. One junk or poorly maintained radio and no one would have known....

Here is a quote:

"All of a sudden, a call came in on the walkie-talkie," said Doug Custer, a co-worker of the trapped men, who escaped the flooded mine ...

Ra

Can we see the outside of the car too?

But, you didn't bolt it down?

Nice Seats.

Ra

Ra

I recently bought one of these from this very seller. I also have a new Motorola RIB and all the official things in my shop too.

This programmer is a very well made & packagede item, and I have used it for a couple of months on many radios.

It works great and does exactly what it should do and is ...

Ra

Very dangerous to ask this question.....

Ra

Monty is right !

Be careful - Ask the pros first, this board has many just waiting to help.

I just purchased for our FD an assortment of special cables and a new Motorola RIB box, and other hardware items from Monty, and could not be more pleased. I recommend him as a great source and am sure ...

Ra

Once - very long ago I worked, and lived, on Mt. Wilson in California.

We had repeaters in the same building as the RCA service company, the guy from RCA was a friend and came up only when something needed fixing. Everything was tubes then.

One day he was coming up the hill to service a system ...

Ra

You are right - 3 antenna it will be then - Extra switching crap is a problem - you are right about that too.

It was just a theoritical question anyway.

Thnaks

Ra

Ra

Our FD built a portable comm center - It consists of 3 VHF M1225 20 channel radios configured as three ac & standby powered bases.

The only hitch is having 3 antennas. One antenna would be nice.

So we thought since cavities would be too big, perhaps we could program the acc connector on the M1225 ...

Ra

Ra

Thanks to all for the input - I can now make the correct decision. This board is great and again thanks for everything!!

We will be getting the P1225s w/ add in QCII board.

Ra

Ra

Nand,

Top of the afternoon to you!

I was speaking with Monty who suggested that an upgradt to the 1225 would eliminate the board option. Makes me think....

This is getting difficult. The FD NEEDS the page option as all 5 FD's are dispatched from one 911 center - each with a different page.

Ra

Ra

Monty,

Thanks for taqking the time to write your considered reply!

You are the man who also knew CR Crtawford I think. Did you also know Bill Miller? Now that would be something! Those were interesting days. I was Crawfords Mt. Wilson guy - I lived up there most of the time keeping the old 2 see ...

Ra

Hi All,

Can someone point me in the right direction??

We need to buy 10 new portables. Anyone who knows where we could best spend our Volenteer FD money would be appreciated.

We need 10 each New SP50 VHF radios with fast chargers. They will need to be 10 channel. On one of those channels a Quick ...

Ra

April, Nice to meet you!

Thank you for the info - it is just what I needed to know.

OK - but please tell..... What is emergency activation?

I have M1225's that have no jumpers and they do everything they should without pins 7&9 jumpered.

Ra

Ra

Monty, this is not my acution, I just happened to see it on Ebay. I had a pair - The transmitter was even more amazing - in my 56' ford. The cables!!

Now they were 6 volts and drew so much current that we also had to put in a ..... a......Lease Nevell alternator, wasent that it?

Yes and the ...

Ra

Most will not - I used to actually tune these guys up as a boy. They were quite good actually, very loud and had a unique squelch tail. . All you needed was a 0-50 microamp meter and a diddlestick and it was "programmed"!

This is one of the rare AC powered ones!

http://cgi.ebay.com/ws/eBayISAPI ...

Ra

P E R F E C T - Just what I needed to hear - soldering is old habit as is opening old Mic's.

Going to bench as we speak!!

Cheers!

Ra

Ra

Does anyone know what part number speakers will ACTUALLY work with the M1225 Series?

Some say that the Maxtrac will not work even though the pinouts are correct?

Cheers!

Ra

Can you old timers tell me where you get your parts?

Do you go to Motorola or an MSS?

Who do you find the easiest to work with?

Any source help from the pros will be appreciated!

I will be needing parts all the time, and it has been years.

What a great Forum this is!

Cheers!

Ra

I noticed that the mic back needs a short, via mic hang up clip, to enable rx PL and scan, etc. Is this addressable via software? Will programming the unit as a "handset" allow the rx to stay in the PL enabled mode all the time?

Cheers

Search found 36 matches

Service Monitor Antenna Part Number ?

SP10 Service Manual Part #

CP100 XTN Radio Tool?

Search Engine Question

P50 Low Band Portable Antenna Part Number ?

Ford Truck Switched 12 Volt Line Color?

NMO Antenna Hole Plug Part Number ??

Speaker Felt Gluing ?

HT1250 or HT750 Model ID Please

Biz

Miners & Radios !

Lets see

Programmer

More is Better

Programming

The Old Days !

Phrawg..............

Combining TX Antennas - Ferite ?

PostTest - An-Tenna

Appreciate the Info!

2 Tone Board

Thanks

Portables Needed !

Thanks!

Old Radios - Old Times

No Codeplug! Remember these?

Thanks Dear Hum!

M1225 Speaker, External

Source for Motorola Parts

RX PL Enable M1225