Batboard

caprice96

I am converting a dash mount XTL5000 O5 to a remote mount. I am also adding a UCM to the radio. On the flex the goes from the brick to the TIB (P/N HKN6190C) the following it printed on the ribbon "Not To Be Used With Version A or B HLN6918 / HLN6919 Secure Interface Board" The interface b...

caprice96

Also have to agree with the Thales Liberty antenna, its the way to go if you can get one

caprice96

Abstract: FCC Narrowband mandate supported System Platforms Affected: UHF and VHF Special Configurations: N/A Description: Beginning January 1, 2011 the Federal Communications Commission will no longer accept applications for new wideband 25 KHz operations, or modifications of existing wideband 25 ...

caprice96

My dept ordered 30 NTN9858C batteries once from /\/\ and they all did the same thing. Just called them in and they sent new ones out and a label to send the old ones back.

caprice96

Yep thats the one, thanks

caprice96

Can anyone tell me if a MHLN6883E will work as a W3 interconnect board for a mid power Astro Spectra?

caprice96

^^like (both the original post and batdudes comment), maybe this means december 21st is the end of the world after all

caprice96

The PMMN4041A is listed as a public safety mic for the XPR portable, my question is can it be used on an APX7000 for 7/800 mhz with proper antenna?

caprice96

Looking for the P/N for a black XTS5000 M3 case/plastic. Dont need one that includes the electronics just the plastic.

caprice96

Question :

Does anything on the repeater side need to be enabled for this to work in ASTRO? I have a repeater that is running in Mixed Mode and I can talk into it fine regularly but when I switch to the mode with the DVRS feature enabled, I get bonked. Any ideas?

caprice96

This sounds like a cool idea, would like to see this idea expand.

caprice96

I have the same problem and im using R12.

caprice96

I have an HT1550 that is used by a corporate security company that just plain wont power up. Yes the battery is charged and I have tried it on other radios. Tried re-seating the two flex cables inside but still nothing. Any ideas? Spec are as follows : Model # : AAH25SDN9DU8AN Firmware Rev : R05.09.15

caprice96

It is a velcro type pad that would go in place of the clip on the back of the mic, I had one and have no idea where its at.

caprice96

Does anyone know what the P/N for the velcro pad that goes in place of the clip on the back of a jedi style public safety mic?

caprice96

How many QC-II systems does an EX600 support?

caprice96

Found the P/N (7502118Z01) but in typical Motorola fashion it is canceled. So unless there is a different P/N I'm SOL. I would imagine their would be a different part number since the XTL5000 stuff hasn't been canceled for that long.

caprice96

Anyone know what the P/N is for the little rubber plug that goes on the front of a spectra to fill the mic whole when the mic is plugged in the back of the control .

caprice96

Ahh ha, I stand corrected.

caprice96

Sounds like he's trying to monitor the Cleveland, Ohio system. That's the only VSELP system left in existence that I know of.

http://www.radioreference.com/apps/db/?sid=562

caprice96

Analog Trunking ID Display is a separate box you need to check off as well.

caprice96

Ok, thanks for the info. Im working with N7MAQ to get one. Thanks for all your help.

caprice96

Ok, thanks Jim appreciate the help, Ill start looking for one.

caprice96

What range is an R2 radio?

caprice96

Does anyone know what it takes to make a UHF Astro Spectra (450-483) function in the ham band on IMBE?

caprice96

As the title says, im looking for the part number for the ZNUP and ZNDN buttons for the spectra. I have searched high and low and can not find them. All I come up with is the PN for the large arrow buttons.

caprice96

Thanks again Marc.

caprice96

Looking for another part number. This time Im looking for the plastic piece that snaps on the back of the radio to help support the RSM.

caprice96

IF you are authorized on the system, then the admin can assist with programming the radio. If not then sell the radio and buy a scanner.

caprice96

Have no idea when V2 is going to be released. The document is on MOL under the resource center.

caprice96

I had this happen on a 5k once, it was the speaker that started to go. Just replaced that and magic no more tinny sound. Thats about the only thing I could think of.

caprice96

Thank you much.

caprice96

Does anyone have the PN for the A version XTS2500 knob. I have a XTS2500 with the B version knob and I prefer the A version. Thanks in advance.

caprice96

Dont forget about IMBE on a low band MCS2000.

caprice96

According to Ma M with release version 2 P25 ID decoding should be supported. " If a customer is using Motorola radios, MIP 5000 can act as a virtual control head giving access to proprietary features from the desktop such as:, display both MDC 1200 and ASTRO PTT- ID's for calls and Emergency A...

caprice96

Will it work if you have the 9600buad trunking firmware in the radio. I have a XTS3000 with r06.71.00. The flashcode does have ID display in it.

caprice96

I have a WPLN4108BR Impress Rack Charger with V3.30 firmware and every time I put a NiCD in it I get the fast blinking light telling me that the battery is not charging and when I put a LiON in it I get the flashing yellow light telling me standby. Both batteries are non-impress and brand new (904)....

caprice96

How is this one compared to Dayton?

caprice96

R12.00.00

caprice96

Being that M/A COM was the low bidder, one could follow that age old adage " You get what you pay for".

caprice96

Does Motorola do things better with putting out a statewide network and the related infrastructure (towers, radios, data systems, etc). I see moto has the Starcom 21 system in Illinois and on googling this I do not see much bad press on this. Motorola must be doing some thing right if they have sta...

caprice96

If you go into the CSDM you need to enable Stat-Alert on each console and then add it to the menu in the console. I will post some screen shots tomorrow and try to go in to detail further. I know it does work over MDC1200 but have never tried anything in P25.

caprice96

Before someone else says it, are you authorized to be on the system?

caprice96

I bought a UHF one off of the guy and I got it set up at home to monitor the local PD. I have not had one problem with it. I replaced the caps for good measure and it is a true champ. For the price they are not a bad deal. Mine had a A7 head on it and it was great shape.

caprice96

All I can say is bravo and works like a charm. A++++ Mike.

caprice96

caprice96

I know this is going to be one of those duhh questions but here it goes. How would you go about programming a Mid Power XTL5000 with a W9 control head? With a spectra you would obviously do it from the rear DB-15 but how would you go about doing it with a XTL5000?

caprice96

Q352 - User Definable ID

caprice96

Brain Fart, sorry about that Tom,

Yep all setup. I set one button to be th keypad lock b/c I have it on the #3 side button on the radio but when I disabled it from the HHCH and the radio still nothing.

caprice96

I guess that would help. The VHF 3K's are also 1C5E's the 800 is legit and the 5K is a whore.

Search found 77 matches